140416
23
Verklein
Vergroot
Pagina terug
1/236
Pagina verder
23
En
Watching TV
06
English
Watching TV
Unless you set up TV channels that you can watch under the
current conditions, you cannot tune in those channels. For the
procedure, see “Setting up TV channels automatically” on page
30.
Turning on/off the power
NOTE
When the Media Receiver is plugged into a power outlet, it is
placed into the standby mode; the STANDBY indicator on its
front panel should flash red. The Media Receiver stays in the
standby mode unless it is unplugged from the power outlet.
To turn on the system, press POWER on the Plasma Display.
The POWER ON indicators on the Plasma Display and Media
Receiver light up in blue.
To turn off the system, press a on the remote control unit or
STANDBY/ON on the Media Receiver.
The Plasma Display and Media Receiver are placed into the
standby mode; their respective STANDBY indicators light up
in red.
You can then turn on the system again by pressing a or 0 to
9 on the remote control unit or STANDBY/ON on the Media
Receiver. If you press 0 on the remote control unit, images
come from the INPUT 1 source. If you press 1 to 9, TV images
display.
You can also press POWER on the Plasma Display to turn off
the system. However, you cannot then turn on the system
again by pressing the buttons on the remote control unit and
Media Receiver.
NOTE
Before operating with the remote control unit, make sure to
select the TV mode using its SELECT button. See “Controlling
other equipment using the supplied remote control unit” on
page 69.
It is recommended not to unplug the Media Receiver from a
power outlet when it is not in use. When in the standby
mode, the Media Receiver automatically receives Electronic
Programme Guide and DTV Auto Update signals.
When the system is placed into the standby mode, the main
power flow is cut and the system is no longer fully
operational. A minute flow of power feeds the system to
maintain operation readiness.
If you are not going to use the Plasma Display System for a
long period of time, be sure to remove the power cord from
the power outlet.
Plasma Display/Media Receiver status indicators
The table below shows the operational status of the Plasma
Display System. You can check the current status of the system
with the indicators on the Plasma Display and Media Receiver.
Plasma Display
Media Receiver
For other than the above, see “Troubleshooting” on page 76.
STANDBY indicator
POWER ON indicator
POWER
button
TIMERSTANDBYON
STANDBY/ON
PULL
OPEN
POWER ON indicator
STANDBY indicator
STANDBY/ON
button
TIMER indicator
1
1 2 3
4 5 6
7 8 9
PC
0
2 3 4
INPUT
INFO
INPUT 5
TV/DTV
SELECT
TV STB
DVD/
DVR
VCR
SOURCE
P
Indicator Status System Status
Plasma Display Media Receiver
POWER ON STANDBY POWER ON STANDBY
The power cords of both the Plasma Display and the Media Receiver have been
disconnected. Or, the power cord of the Plasma Display has been connected but
the POWER button of the Plasma Display is off.
Power to the system is on.
The system is in the standby mode.
Flashing
The power cord of the Media Receiver has been disconnected.
Flashing
Power to the Plasma Display is off. Or the power cord of the Plasma Display has
been disconnected.
PDP506XDE.book Page 23 Friday, June 17, 2005 3:08 PM
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer 506 xde bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer 506 xde in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 13,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Pioneer 506 xde

Pioneer 506 xde Gebruiksaanwijzing - Nederlands, Italiano, Espanôl, Espanõl - 236 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info