492033
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
© 2010 Phoenix Gold • www.phoenixgold.com
Amplier Owners Manual
Power Output:
RMS Power 16.0Vdc 8000 x 1 @ 2 ohm
12000 x 1 @ 1 ohm
24000 x 1 @ 2 ohm (Strapped)
RMS Power 14.4Vdc 5000 x 1 @ 2 ohm
8000 x 1 @ 1 ohm
16000 x 1 @ 2 ohm (Strapped)
SPL “Burping” Power 16.0Vdc 10000 x 1 @ 2 ohm
18000 x 1 @ 1 ohm
36000 x 1 @ 2 ohm (Strapped)
INPUT
Connect preamp signal cables from the head unit to these terminals.
OUTPUT
Provides a full range signal for an additional amplier. There is no signal
loss if using this output.
LP FREQ
Controls the lowpass crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +6dB @ 45 Hz.
LOW PASS LEVEL CONTROL (LPL)
This port is for connecting the optional remote level control (LPL44).
This allows up to 20dB of volume adjustment. This is not a bass boost, it
controls the level of the low pass signal.
LEVEL
Used to reach maximum amplier power with a wide variety of headunits.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. Minimum impedance is 1 ohm. 8 gauge
wire is required.
SUBSONIC
Controls the subsonic (highpass) crossover point for the speaker outputs to eliminate
extreme low frequencies.
PROTECT LED
Lights red if there is a problem with the audio system. For example, speaker wire is
pinched/shorted together or the amplier is running too low of an impedance.
INPUT SLAVE/OUTPUT MASTER SWITCH
For normal use, the switch MUST be set to OUTPUT MASTER”. If linking or strapping
two ampliers together please see page 7 for more details. IMPORTANT: In normal or
single amplier use there will be no output if this switch is set to “INPUT SLAVE”. Be
sure it is set to “OUTPUT MASTER”.
+12V
This must be connected to the fused positive terminal (+12V) of the cars battery. See
page 4 for an electrical system example. 1/0 gauge wire is required.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming from the head
unit or ignition.
GND
This must be connected to the negative terminal of the car’s battery or bolted to a
clean, unpainted part of the chassis of the vehicle. 1/0 gauge wire is required.
COntrols
REMOTE MONITORING DISPLAY (RMD)
Connect optional RMD Voltage Display to this port.
IMPORTANT: ALL THREE POWER TERMINALS MUST
BE USED. DO NOT USE ONLY ONE OR TWO OF THE
TERMINALS, IT CAN DAMAGE THE AMPLIFIER.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Phoenix Gold The one bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Phoenix Gold The one in de taal/talen: Engels als bijlage per email.

De handleiding is 2,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info