492020
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Amplier Owners Manual
© 2011 Phoenix Gold • www.phoenixgold.com
System tuning
TROUBLESHOOTING
1. Install all system fuses.
2. Set the amplier’s input sensitivity controls to their minimum positions
(full counterclockwise).
3. Set all amplier crossover switches according to your systems design.
4. Make preliminary adjustments to the crossover frequency, usually 80Hz
is good starting point for high and low pass. It may be necessary to ne
tune the crossover frequency later for the best overall sound quality.
5. If using a Remote Subwoofer Level Control, set it to maximum (full
clockwise).
6. Turn the headunit on with the volume set to minimum.
7. Visually check the amplier’s has turned on by the power LED.
8. Check the condition of all other components to make sure they are
powered up.
9. Set the headunit’s tone controls, balance, and fader to the center (at)
position. Turn o any loudness or other signal processing features.
10. Set the volume control of the headunit for maximum undistorted output
(on most headunits this will be approximately 7/8 of maximum volume).
Use a very clear and dynamic recording.
11. Turn up the sensitivity or input level control on the amplier until the
speakers reach maximum undistorted output.
12. Repeat sensitivity level adjustments for all other ampliers.
13. Reduce the headunit’s volume to a comfortable level.
14. Listen to various musical selections to check overall system balance.
Compare front to rear, midbass to midrange, etc. If one speaker set is
too loud compared to another, then its level must be lowered to blend
correctly with the other speakers.
Note: For subwoofers controlled by the Remote level control, keep the
level setting from step 11 or 12. Use the control to blend subwoofers
with the rest of the system. The correct subwoofer volume will change
depending on road noise and dierences in recordings.
15. Fine tune crossover frequencies to achieve the smoothest possible
blending of each speaker set.
16. Adjust the Bass Equalization Controls on the amplier, headunit or
processor upstream if necessary to increase output.
Note: Use these controls sparingly. Every 3dB of boost requires double the
power at 45Hz. If your subwoofer system requires a lot of boost to sound
good, there may be a problem. Look for out-of-phase woofers, a leaking
subwoofer box, or incorrect box size.
17. With all levels set correctly, the system will reach overall maximum
undistorted output at the volume level set in step 10.
OVERVOLTAGE WARNING - If the voltage is above 14.4V across the +12V and
ground terminal this will cause the amplier to go into protection mode. The
result is no audio output from one or more channels. Voltage must between
11.5V to 14.4V for the amplier to operate correctly.
No power: Check voltage at the amplier with a DMM (volt meter), +12v and
R (with head unit on) the voltage should register between 11.5V and 14.4V
when using the attached ground lead of the amplier. Check fuse at amplier
and at the battery. Use a meter to verify connection from one end of the fuse
to the other, breaks may not always be visible. If the fuse is blown, check the
power wire and also the amplier for a short. If the short is in the amplier
itself, see your Phoenix Gold dealer. If no short is present, replace the fuse.
Power without sound: Turn the amplier o and check all input and output
signal cables and power connections. Check the speakers for shorts with
a DMM (volt meter) or by connecting them to another audio source. After
making sure everything is correct, turn the amplier on again.
Power without sound and the PROTECT LED is lit: The red PROTECT LED
lights when the amplier shuts down for either thermal or over-current
protection. A high internal amplier operating temperature will trigger
thermal shutdown: after it cools about 5°C, the amplier will restart. A
shorted speaker lead or operation into unusually low impedance loads will
trigger over-current shutdown: cycle power at the amplier R terminal to
restore operation. Check for shorted speaker wiring or damaged speakers or
crossover systems if over-current shutdown occurs.
No sound from one or more channels: Check for overvoltage on +12V and
ground terminals. Check the balance control in the head unit. Check speaker
connections. Check signal input connection.
Very low output: Check your head unit’s fader control or the amplier’s input
sensitivity level. Make sure subsonic frequency control is not set too high and
LP frequency control is not set too low at the same time.
Frequent amplier shutdown with automatic recovery: This indicates
chronic amplier thermal shutdown because of operation at consistently
high internal temperatures. High operating temperature can be caused
by inadequate ventilation. Make sure you are not running a lower than
recommend impedance. Also check for damaged speakers or passive
crossover systems. Finally, chronic thermal shutdown may result from
otherwise normal operation of the amplier at elevated output power levels,
which can be resolved by providing additional amplier cooling, installing a
higher-power amplier, or reducing amplier output level.
“Motor Boating” - the power indicator going o repeatedly when the audio
system is on: Check the amplier’s connection to the battery. Check battery
voltage. If low, recharge or replace the battery. Check all ground connections.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Phoenix Gold SD200.2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Phoenix Gold SD200.2 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info