492013
5
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
Elite Amplier Owners Manual
© 2012 Phoenix Gold • www.phoenixgold.com
© 2012 Phoenix Gold • www.phoenixgold.com
Elite Amplier Owners Manual
All crossover frequency potentiometers have 41 detents or clicks” so the end user can set the exact crossover frequency desired.
ELITE.1
clicks
Subsonic
(10~55Hz)
LPF
(30~300Hz)
1 12 30
2 12 30
3 12 30
4 12 30
5 12 30
6 12 31
7 13 32
8 13 33
9 14 35
10 15 37
11 16 39
12 16 42
13 18 45
14 19 49
15 20 52
16 22 56
17 24 62
18 26 69
19 28 77
20 31 87
21 32 102
22 34 114
23 35 120
24 36 126
25 38 134
26 39 143
27 40 152
28 42 163
29 44 214
30 45 230
31 47 248
32 47 251
33 48 253
34 48 260
35 49 273
36 49 280
37 49 289
38 49 295
39 50 304
40 50 305
41 50 306
CROSSOVER SETTINGS
ELITE.2
clicks
LPF
(40Hz~4khz)
HPF
(20Hz~4kHz)
1 37 23
2 37 24
3 38 24
4 38 25
5 41 27
6 44 29
7 48 30
8 51 31
9 56 33
10 62 37
11 68 40
12 76 44
13 88 50
14 96 55
15 110 58
16 130 67
17 160 78
18 180 99
19 190 120
20 220 121
21 250 150
22 290 170
23 330 200
24 360 220
25 430 260
26 480 360
27 560 390
28 620 430
29 720 450
30 970 631
31 1.18k 790
32 1.3k 890
33 1.5k 1k
34 1.7k 1.18k
35 2k 1.4k
36 2.45k 1.7k
37 2.7k 2.2k
38 3.2k 3.2k
39 3.5k 4.15k
40 3.85k 4.2k
41 3.9k 4.4k
ELITE.4
clicks
LPF
(40Hz~4kHz)
HPF
(20Hz~4kHz)
1 36 24
2 37 25
3 38 27
4 41 30
5 44 33
6 48 38
7 52 41
8 55 46
9 61 51
10 65 60
11 67 71
12 73 83
13 86 96
14 93 106
15 99 122
16 107 129
17 127 134
18 162 143
19 186 155
20 220 170
21 251 187
22 282 207
23 317 235
24 365 264
25 430 286
26 517 330
27 666 353
28 860 393
29 1.05k 434
30 1.12k 455
31 1.32k 514
32 1.49k 583
33 1.65k 693
34 1.77k 876
35 2k 1k
36 2.3k 1.2k
37 2.5k 1.4k
38 2.9k 1.8k
39 3.2k 2.6k
40 3.6k 3k
41 3.9k 4.2k
FRONT AND REAR INPUTS
Connect preamp signal cables from headunit to these inputs. The front
and rear inputs must be used, if only the front input is used then the rear
speaker outputs will have no output signal.
FAN
The internal fan is nearly inaudible but the end user can control the fans
mode via the endpanel switch.
ON:
Fan runs at full speed at all times regardless of the heatsink
temperature. This is recommended for heavy users or low impedance
loads such as 1 ohm stereo/2 ohms bridged.
OFF:
Internal fan is o. This is only recommended for short periods of
time. For example, a sound quality competition.
AUTO:
Best setting for most users. Internal fan is o until the heatsink
temperature reaches 50°c/120°F then the variable fan turns on and its
speed is controlled by the heatsink temperature.
REMOTE LEVEL CONTROL
This port is for connecting the subwoofer remote level control. This is not a bass
boost, it controls the level of the low pass signal of
rear channels only
. Rear channels’
cong switch must be set to “LP/BP” for the remote to operate.
CROSSOVER FREQUENCY
Controls the crossover point for the speaker outputs. See page 8 for exact crossover
settings.
LEVEL
Used to reach maximum amplier power with a wide variety of headunits.
CONFIG
FLAT:
Crossovers are turned o
HP:
High pass crossover is on
LP/BP:
Low and High Pass crossovers are on, creating a Bandpass (BP) setting for
midbass drivers or subwoofers. For a standard subwoofer system, the high pass
frequency now becomes a subsonic lter. To turn subsonic lter o, turn the HP
FREQ (Subsonic Filter) to 20Hz.
+12V
This must be connected to the fused positive terminal (+12V) of the cars
battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming
from the head unit or ignition.
GROUND
This must be connected to the negative terminal of the car’s battery or
bolted to a clean, unpainted part of the chassis of the vehicle.
RMD
Optional RMD Voltage Display plugs into this port. Sold separately.
CLIP INDICATOR
Lights when the amplier reaches near maximum output. Under normal
operation the clip indicator should be ashing during the peaks of the
music. The clip indicator should not stay lit for long periods of time (more
than 2 or 3 seconds), if this is the case you need to reduce system volume
or level of the amplier.
PROTECT INDICATOR
Lights red if there is a problem with the audio system. For example, speaker
wire is pinched/shorted, the amplier is running too low of an impedance
or reached an unsafe temperature.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. Minimum impedance is 2 ohms
bridged or 1 ohm stereo. Minimum speaker wire size is 16 gauge. Use Left
+ and Right - to bridge the channels.
ELITE.4 FUNCTIONS
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Phoenix Gold Elite bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Phoenix Gold Elite in de taal/talen: Engels als bijlage per email.

De handleiding is 5,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info