480
28
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
Notes:
If the Temperature warning indicator lights up, follow the
above possible solutions and then wait until the projector has
cooled down completely before turning the power back on.
(At least 5 minutes.)
If the power is turned off and then turned on again, as during
a brief rest, the Lamp indicator may be triggered, preventing
the power from going on. Should this occur, take the power
cord out of the wall outlet and put it back in again.
Lamp (LCA 3110; 8670 931 10009)
The lamp in this projector operates for approximately 2000
cumulative hours, depending on the usage environment. It is
recommended that the lamp be replaced after 1900 cumulative
hours of use or when you notice a significant deterioration of
the picture and colour quality. The lamp usage time can be
checked with the On-screen Display
(see page 23).
CAUTION!
Intense light hazard. Do not attempt to look into the aperture
and lens while the projector is operating.
As the usage environment can vary significantly, the
projector lamp may not operate for 2000 hours.
Replacing the lamp
1.
Unplug the power cord.
Press Power OFF. Wait until the cooling fan stops.
2.
Disconnect the powercord
Disconnect the mains lead and all the other cables.
3.
Slide the lamp cage cover out.
Turn over the projector and unfasten the user service screw
that secures the lamp cage cover. Then slide the cover in
the direction of the arrow.
4.
Remove the lamp cage.
Remove the securing screws from the lamp cage.
Hold the lamp cage by the handle and pull it towards you.
5.
Replace the lamp cage (after changing the lamp).
Press the lamp cage firmly into the lamp cage
compartment. Fasten the securing screws.
6.
Slide the lamp cage cover in.
Slide the lamp cage cover in the direcrtion of the arrow.
Then fasten the user service screw.
CAUTION!
Do not remove the lamp cage directly after operation of the
projector. The lamp may be extremely hot. Wait at least one
hour after the power cord is disconnected to allow the
surface of the lamp cage to fully cool before removing the
lamp cage.
Be sure to remove the lamp cage by the handle. Be sure not
to touch the glass surface of the lamp cage or the inside of
the projector.
26
9. ADDITIONAL INFORMATION Maintenance
English
Maintenance Indicator Condition Problem Possible Solution
TEMP. The internal Blocked air intake. Relocate the projector to an area with
WARNING indicator temperature is proper ventilation.
(Temp) abnormally high. Clogged air filter. Clean the filter.
(see page 25.)
Cooling fan breakdown. Take the projector to your nearest
Internal circuit failure. Authorized Philips Industrial LCD
Products Dealer or Service Center for
repair.
LAMP indicator The lamp does not Burnt-out lamp. Carefully replace the lamp.
(Lamp) light up Lamp circuit failure. (See page 26.)
Take the projector to your nearest
Authorized Philips Industrial LCD
Products Dealer or Service Center for
repair.
POWER INDICATOR The POWER indicator The bottom filter cover Securely install the bottom filter cover.
z / y flashes in red when the is open.
projector is on.
Securing screws
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Philips ProScreen PXG10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Philips ProScreen PXG10 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 3,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Philips ProScreen PXG10

Philips ProScreen PXG10 Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info