493720
5
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
CCTVSET10
26/05/2011 ©Velleman nv
5
Connecting the mouse
Plug the USB-mouse connector into the USB input [22] at the rear of the DVR.
Connecting external alarms / RS485
When desired, connect external alarm inputs (e.g. from door/window contacts) to the alarm input connector
[13].
Connecting ground
Connecting the ground terminal [14] to earth might resolve any image interference problems. Do not
connect when the image is fine.
Connecting the power supply
Plug a DC output connector of the included power adaptor into the 12VDC power input [15] at the back of
the DVR.
WARNING: only use the included adaptor.
Plug the included power cable into the adaptor input connector and plug the other end into the mains.
Switch to DVR on with the ON/OFF switch [12].
Connecting Local Area Network (LAN)
Connect the DVR to a local network by plugging a network cable into the LAN port [21] at the back of the
DVR. Connector type is 8P8C (RJ45). Setup is done through the OSD.
7. Operation
Note: the functions, navigation and options of the DVR are accessible via the front panel, the remote control
or by using the mouse.
Switching on the DVR with the ON/OFF switch [12] at the back. It takes about 45 seconds for the
initialization to complete and to show live images.
After start-up, the power LED [6] is on and the display shows the 4 camera channels simultaneously. Date
and time is shown in the top area of the display. Should one of the images remain blank, check the camera
and cabling of that channel.
Press the LCD power switch [2] to switch the LCD screen on or off. This does not interrupt the recording
operation of the DVR!
Standby Mode
The system can also be put into standby mode. Power will remain to the system but recording is disabled.
To start/stop Standby mode:
Press and hold the STANDBY button on the front panel [2] or remote control [A] until the
progress bar filled up completely. The system enters standby mode.
Press and hold the STANDBY button on the front panel [2] or remote control [A] for ±3 seconds.
The system will power up again.
Password
ATTENTION: By default, passwords are disabled on the system. You do not need to enter a password
when accessing any system menu. However, for security purposes, it is highly recommended to
enable passwords on the system using the password menu. Refer to §7.3.4.
NOTE:
If there is no HDD in device, or the device can’t read the HDD, or the HDD isn’t formatted, a [H] is
displayed in the video preview interface.
The HDD in the DVR must be formatted before first use. Refer to §7.3.3.
7.1 General menu guidelines
Enter the menu of the DVR by either pushing the MENU-button on the front panel [4] or remote control,
or click the right mouse button, select ‘MAIN MENU’ and click left.
NOTE: If passwords are enabled on the system, you need to select your Device ID and enter the 6-digit
numerical password to open the Main Menu (see §7.3.4).
7.2 Screen image
Front panel controls:
Press the channel selector [2] repeatedly to scroll through the 4 channels or see all four channels
simultaneously.
Remote control:
Press on a numbered channel button (1~4) to see that channel full screen. Press the button to return to
the quadruple display.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Perel CCTVSET10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Perel CCTVSET10 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 4,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info