595357
11
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
11
GB IE
5. Drill the hole until the depth stop
(2) comes in contact with the
component part.
Inserting/replacing the tool
1. Open the keyless chuck (4) wide
(RELEASE) so that the tool can
be inserted. To do so, rmly hold
the rear sleeve (4a) of the keyless
chuck (4) and turn the front sleeve
(4b) in the anti-clockwise direc-
tion.
2. Insert the tool as far as possible
into the keyless chuck (4).
3. Close the keyless chuck (4) (GRIP)
in order to clamp the tool. To do
so, rmly hold the rear sleeve
(4a) of the keyless chuck (4) and
turn the front sleeve (4b) in the
clockwise direction.
4. To remove the tool again, rotate
the keyless chuck (4) and pull out
the tool.
Always use a universal bit holder
use using a screwdriver bits.
Operation
Do not use the device with-
out the additional handle. It
provides additional hold and
reduces the risk of injury.
Observe noise control and local
regulations.
Switching on and off
1. Connect the machine to the pow-
er supply.
Make sure that the net voltage
matches the voltage rating indi-
cated on the device’s type plate.
2. Switching on: Press the on/off
switch (8).
3. By using the on/off switch (8)
you can progressively control the
speed.
Gentle pressure: low speed
Increase pressure: higher speed.
4. Continuous operation: Press the
lock button (9). The on/off switch
(8) is locked.
5. Switching off: Release the on/off
switch (8).
For continuous operation, briey
press the on/off switch (8).
Pre-select speed
You can pre-select the maximum speed on
the speed adjusting ring. The on/off switch
can only be pressed up to the specied
speed.
1. Wait for the device to shut-down.
2. Set the desired speed
on the speed adjusting
ring (7).
Set the direction of rotation
The device’s direction of rotation can be
changed with the rotational direction
switch.
1. Wait for the device to shut-down.
2. Push the rotational direction
speed (6) into the desired posi-
tion:
Clockwise rotation: to drill
and screw in screws.
Anticlockwise rotation: to
loosen screws.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PSBM 500 B3 - IAN 102531 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PSBM 500 B3 - IAN 102531 in de taal/talen: Duits, Engels, Frans, Deens, Zweeds, Fins als bijlage per email.

De handleiding is 4,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info