679220
8
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
PFS 400 A1
GB
IE
NI
CY
 5
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Additional safety instructions for
paint spray guns
Keep your work area clean, well lit and free
of paint and solvents, cloths and other inflam-
mable materials. Possible risk of spontaneous
combustion. Have a fully functioning fire extin-
guisher available at all times.
Ensure adequate ventilation in the spray zone
and sufficient fresh air in the entire room.
Evaporation of flammable solvents will cause an
explosive environment.
Do not spray or clean with materials whose
ignition point is lower than 21°C. Use ma-
terials based on water, non-volatile hydro-
carbons or similar materials. The evaporation
of volatile solvents will cause an explosive
environment.
Do not spray near ignition sources such as
static electric sparks, open flames, ignition
flames, hot items, motors, cigarettes or sparks
caused by plugging in/unplugging power
cables or by operating switches. These ignition
sources could ignite a fire in the environment.
Do not spray any material if you do not know
whether it is potentially dangerous. Unknown
materials can cause hazardous conditions.
Wear additional personal protective equip-
ment such as suitable gloves and a protective
mask/respirator when spraying or handling
chemicals. Wearing appropriate protective
equipment for the conditions reduces your expo-
sure to dangerous substances.
Be aware of the potential hazards of the
sprayed material. Take note of the markings
on the container and the manufacturer's infor-
mation on the sprayed material, including the
instructions to use personal protective equip-
ment. The manufacturer's instructions are to
be followed to reduce the risk of fire or injuries
caused by poisons, carcinogens, etc.
Do not use the spray gun to spray flammable
substances. Do not clean spray guns with flam-
mable solvents.
WARNING!
Be aware of any dangers inherent to the
spray material and pay attention to all pack-
aging labels and other information provided
by the producer of the substance.
Working procedures
Viscosity
The appliance can process spray materials up to a
maximum 70 DIN/s. (viscosity). You can deter-
mine the viscosity (thickness) of the substance with
the supplied measuring cup using a simplified
measuring procedure.
Fill the supplied measuring cup to the brim
with the spray material.
Remove the measuring cup from the spray
material and allow the liquid to run out.
Measure the time (in seconds) until the stream
of liquid stops. The resulting value is referred to
as DIN seconds (DIN-s).
If the value is too high, gradually thin the spray
material by adding small amounts of a suitable
thinning agent in and mixing the liquid.
Measure the DIN seconds again. Repeat the
process until you measure a viscosity of less
than 70 DIN/sec.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PFS 400 A1 - IAN 307721 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PFS 400 A1 - IAN 307721 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Parkside PFS 400 A1 - IAN 307721

Parkside PFS 400 A1 - IAN 307721 Gebruiksaanwijzing - Nederlands, Deutsch, Français - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info