595292
31
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
31 GB
Preparing for useGeneral safety advice for electrical power tools / Preparing for use
Q
The planing process
CAUTION! DANGER OF KICKBACK!
Always switch on the device before placing it
against the workpiece.
Set the required cutting depth.
Switch on the device.
Always place the front part of the sole
9
down
first on to the workpiece.
Guide the device with even forward movement
over the surface being planed.
Move the device forward at a slow rate and
ensure that the contact pressure acts evenly on
the sole
9
. Moving forward at too great a rate
results in a poorer surface quality and can lead
to blocking of the planing debris removal port.
Q
Chamfering edges (see Fig. H)
The V-grooves
10
in the front sole
9
allow the de
vice
to be used for simple chamfering of workpiece edges.
Use the V-groove most appropriate to your
desired chamfer width.
Place the planer with the V-groove
10
on the
work-
piece edge and guide the planer along the edge.
Q
Using the guide fence (see Fig. I)
Attach the guide fence
6
to the device with
the fixing screw
7
.
Release the fixing nut
8
and set the guide at
the desired distance.
Retighten the fixing nut
8
.
Exert some slight sideways pressure when guid-
ing the planer with the guide fence.
Q
Using the rebate depth stop
(see Fig. J)
Attach the rebate depth stop
12
to the device
with the fixing screw
11
.
Set the desired rebate depth with the rebate
depth stop
12
.
Make the required number of passes with the
planer until desired rebate depth is achieved.
Q
Removing and installing a
planer blade
20
(see Fig. D + E)
DANGER OF INJURY!
Before you carry out any work on the device always
pull the mains plug out of the mains socket.
CAUTION! The sharp cutting edges of the plan-
er blade
20
present an injury hazard! Never
touch the cutting edges of the planer blade
20
.
The planer blade
20
has two cutting edges and it
can be fitted either way around.
Replace the planer blade
20
when both cutting
edges are blunt.
Do not resharpen the planer blades
20
.
Reversing or replacing a planer blade
20
IMPORTANT INFORMATION:
Do not release the two Allen keys. They are used to
adjust the height of the blade shaft.
Adjustment is necessary only if you wish to use a
different planer blade type e.g. a profiled blade.
Always replace both blades at the same time to
avoid out of balance forces.
NOTE: If you only release one blade first then you
can use the factory-fitted second blade for orientation
when you fit the new blade.
1. Release the 3 bolts of the cutting element
18
using the supplied open spanner
26
.
Press the removable side guard
21
into the slot
in the housing.
2. Push the cutting element
18
sideways out from
the blade shaft
17
.
3. Push the planer blade
20
sideways out from
the cutting element
18
.
4. Reassembly is carried out in the reverse order
with a reversed or new planer blade.
5. Planer blades
20
can be obtained from the
service address indicated (see section about
warranty).
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PEH 30 A1 - IAN 93528 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PEH 30 A1 - IAN 93528 in de taal/talen: Frans als bijlage per email.

De handleiding is 2,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Parkside PEH 30 A1 - IAN 93528

Parkside PEH 30 A1 - IAN 93528 Gebruiksaanwijzing - Nederlands, Deutsch, English - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info