595286
36
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
36 GB
Cleaning and storage / Information about warranty and service processing
Start-up / After initial use / Cleaning and storage
Verify the air hose is properly seated (see Fig. D).
A loose hose whipping about out of control pre-
sents a major hazard. The coupler must be tightly
seated for the same reason. Also check this.
Cutting
Activate the trigger
2
to start using the shears.
Move the metal shears toward the item you wish
to work on. If possible, already run the shears
at full speed when applying them.
Note: The shears may take up to 8 seconds to
be fully ready for use and reach full force. Dur-
i
ng this time you should wait before applying th
e
shears to ensure better cutting results and treat
the device with care.
Note: Do not apply too much pressure whilst
cutting. Do not overburden the shears. In additio
n
to possible unclean cutting results, this could also
cause metal slivers to chip off and fly about.
Note: Metal slivers flying about can be very
dangerous!
Note: If the compressed air supply is tempo-
rarily cut off due to power failure or temporary
compressor failure, immediately release the trig-
ger
2
. If you now wish to continue working,
you must first remove the metal shears all the
way out of the work piece. You can then con-
tinue working.
When using the device always be aware of the
following items:
The shears must always operate at full speed.
This means, the compressor must always supply
sufficient pressure and air volume.
- Work slow. Slowly guide the shears along the
work piece and work without applying exces-
sive pressure.
- Move the shears smoothly.
- Do not tilt the shears.
Please tighten the screws of the cutter head re-
gularly and replace worn or damaged cutting
edges if necessary (see Fig. E).
Use the corresponding Allen key when doing this.
Check the cutter head after 2 minutes of conti-
nuous operation to ensure it is securely seated.
After initial use
Once the task has been finished the equipment must
be disconnect from the compressed air supply.
This first requires the pressure to be completely re-
leased from the lines.
To release potentially remainders of compressed
air, briefly activate the trigger
2
of the device.
Pull back the lock.
Take off the coupler.
Spare parts / replacing
consumables
When replacing items, always be sure the com-
pressed air supply is disconnected!
N
ote: The shear head does not necessarily ha
ve
to be removed all the way. After loosening the
screws you can remove the parts of the cutter
blades to replace the defective part.
Use a fitting hex wrench to loosen the screws on
the underside of the shear head (see Fig. E). Re-
move the blades and replace the defective part.
During assembly be sure the blades are corre
ctly
aligned.
First insert the lower blade.
Then insert the centre piece.
Then insert the marked ring. This is merely a spacer
between the upper and lower blade.
Now insert the upper blade and secure the shear
head with the screws.
Note: please note, the notches on the blades
must face the inside.
Cleaning and storage
To ensure a long life and trouble-free operation, it‘s
important to observe the following instructions.
Always disconnect the tool from the compressed
air source before cleaning it.
Clean your tool with a soft, dry cloth or lightly
blow it out with compressed air. Never use
caustic cleaners.
43096_par_Druckluft-Blechschere PDBS 6.2A1_content_DE_NL.indd 36 28.05.14 16:57
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PDBS 6.2 A1 - IAN 43096 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PDBS 6.2 A1 - IAN 43096 in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 2,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info