745112
40
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
40 GB
Initial use / Maintenance and CleaningSafety advice / Initial use
Do not spray any materials for which
it is not known whether they pose a
danger. Unknown materials can create dan-
gerous conditions.
Wear additional personal protective
equipment such as appropriate protec-
tive gloves and protective masks or
respirators when spraying or handling
chemicals. The wearing of protective equipment
in such conditions reduces exposure to harmful
substances.
Do not spray on yourself, other people
or animals. Keep hands and other body
parts away from the spray jet. If the
spray penetrates the skin, seek medical help
immediately. The material being sprayed can
even penetrate the skin through a glove and be
injected into your body.
Do not treat an injection as a simple cut.
A high pressure jet may inject toxins
into the body and cause serious inju
ries.
If the spray is injected into the skin, seek medical
help immediately.
Pay attention to any possible dangers
of the material being sprayed. Note
the markings on the container or the
manufacturer’s information relating to
the material being sprayed, including
the instruction to use personal protec-
tive equipment. The manufacturer’s in-struc-
tions must be followed to reduce the risk of fire, as
well as injuries caused by toxins, carcinogens, etc.
Never spray without the nozzle head
in place. The use of a special nozzle insert
with the appropriate nozzle head reduces the
probability of a high-pressure jet penetrating
the skin and injecting toxins into the body.
Q
Initial use
Q
HVLP properties
This device uses an HVLP system (High Volume Low
Pressure). It ensures the increased application of
(paint) materials with lower consumption.
Important: Do not exceed the maximum working
pressure of 3 bar.
Q
Connecting the device
Operate the product only with cleaned, con-
densate- and oil-free compressed air and never
exceed the maximum working air pressure at
the device of 3 bar.
The compressed air source must be fitted with a
(filter) / pressure reducer so that the air pressure
can be regulated.
In order to operate this device you require a flexible
compressed air hose with quick-release coupling
and an appropriate source of compressed air.
Observe the operating and safety instructions of the
compressed air source and any special instructions
concerning paint preparation.
Note: Ensure the correct working pressure. An
excessive working pressure leads to increased fine
dispersion and results in too rapid evaporation of
the liquid. The surfaces become rough and develop
poor adhesion properties. If the working pressure is
too low on the other hand, the paint material is not
sufficiently atomised. Undulating surfaces and the
formation of drops are the result.
Connect the compressed air hose with the
rapid-release coupling to the compressed air
connection
6
of the device. This automatically
locks into place.
Use the filter pressure reducer of the compressed
air source to set the working pressure to 3 bar.
Q
Preparing the spraying surface
Mask off the surroundings of the spraying surface
thoroughly over a wide area. Otherwise all non-
covered areas or surfaces may become soiled.
Make sure that the spraying surface is clean,
dry and free of grease.
Roughen smooth surfaces and then remove the
sanding dust.
Q
Turning the device On / Off
Working Instructions:
- Insert the filter in the gun (see Fig. C).
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 89567 PDFP 500 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 89567 PDFP 500 A1 in de taal/talen: Nederlands, Duits, Frans, Italiaans als bijlage per email.

De handleiding is 0,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info