745457
35
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
35 GB
General safety rules
General safety rules / Before use / Start-up
because the risk from vibration is generally gr
eater
when the grip force is higher.
Additional safety instructions
for pneumatic power tools
Air under pressure can cause severe injury:
always shut off air supply, drain hose of air
pressure and disconnect tool from air supply
when not in use, before changing accessories
or when making repairs;
never direct air at yourself or anyone else.
Whipping hoses can cause severe injury. Always
check for damaged or loose hoses and fittings.
Cold air shall be directed away from hands.
Whenever universal twist couplings (claw cou-
plings) are used, lock pins shall be installed
and whipcheck safety cables shall be used
to safeguard against possible hose-to-tool or
hose-to-hose connection failure.
Do not exceed the maximum air pressure stated
on the tool.
Never carry an air tool by the hose.
General safety
instructions for compressed
air metal shears
Always wear safety gloves.
Be careful whilst working with the shears. Edges
created on the work piece can cause cuts.
If possible, already run the shears at full speed
when applying them. Otherwise sudden, jerky
movement could result if the shears catch when
starting up at the front, resulting in backlash.
Before use
Installation
The device itself is fully functional at delivery. You
will need to install a coupler before using the de-
vice itself (please note the data specified under
technical details for accuracy of fit/size).
Wrap the coupler with Teflon tape (not included)
before screwing it into the compressed air unitn.
Wrap the tape as tightly as possible around
the thread. This will minimise the likelihood of
air leaking and optimise the work process.
Now screw the coupling into the compressed
air equipment.
Tighten the coupler into the compressed air unit
with a size 14 spanner using moderate force
(see Fig. A).
Adjusting the compressed air supply and
connections
Only use filtered, lubricated and regulated com-
pressed air.
Apply the connection method on the compressed
air unit shown in Fig. B. This will increase the ef-
fectiveness and life of the tool.
Set your compressor to the device‘s operating
pressure specified under Technical Data. Please
note, on average the pressure for 10 m of hose
will decrease by about 0.5 bar.
Excessive pressure is dan-
gerous! Never exceed the specified pressure!
Add a few drops of oil for compressed air tools
or SAE 10–20 motor oil to the compressed air
c
onnection of the compressed air unit. Using othe
r
oil (esp. viscous) will result in malfunctions, dam-
age or even total loss of the device.
Start-up
Connecting the
compressed air tool
Verify the work piece is properly secured.
Connect the compressed air by pushing on the
coupler of the hose with some force (see Fig. C).
Verify the air hose is properly seated (see Fig. D).
A loose hose whipping about out of control pre-
sents a major hazard. The coupler must be tightly
seated for the same reason. Also check this.
109803_par_Druckluft-Blechschere PDBS 6.2A1_content_FR.indd 35 09.04.15 16:09
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 109803 PDBS 6.2 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 109803 PDBS 6.2 A1 in de taal/talen: Frans als bijlage per email.

De handleiding is 2,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Parkside IAN 109803 PDBS 6.2 A1

Parkside IAN 109803 PDBS 6.2 A1 Gebruiksaanwijzing - Nederlands, Deutsch, English - 39 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info