135078
15
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
VQT9002
15
The remote control does not work correctly
The signal from the remote control does not reach the VCR’s window,
or the distance is too long.
Remove obstructions between the VCR and the remote control
(its transmitting distance is about 7 metres).
The batteries in the remote control are exhausted, or the batteries have not been
inserted with the correct polarity.
Check the batteries and if necessary insert new batteries (see page 2).
The VCR is set to Power save mode.
Settings can be changed (see page 9).
The recording function does not work correctly
The VCR display is flashing when you try to record.
In order to record, use a video cassette with an intact erasure
prevention tab (see page 6).
The Programmed recording function does not work.
The time and date must be set correctly (see page 8).
The VCR does not record, even though the recording has been programmed.
Set the start time and the time to stop recording correctly, and set the VCR
on Standby Recording by pressing the TIMER Button (see pages 6-7).
Tape transport noise
During JET SEARCH the tape transport noise will increase.
These is not a functional fault.
If problems occur which you cannot deal with yourself,
consult a service center (see the Guarantee Information).
Before Requesting Service
The VCR display is not illuminated:
The mains lead is not connected.
Check the connection.
The VCR is set to Power save mode.
Settings can be changed (see page 9).
The VCR display is set to OFF.
Settings can be changed (see page 9).
Safety devices are operating.
Disconnect the VCR from AC mains for one minute,
then check if the VCR can be operated.
The VCR display is illuminated, but the VCR cannot operate:
The VCR is in Timer recording Standby mode.
Cancel Standby mode by pressing the TIMER Button.
The child lock is activated.
Settings can be changed (see page 8).
The picture or the sound is distorted:
The TV reception is not adjusted to the VCR.
Readjust the reception (see page 3).
The tracking is not set correctly.
Adjust the tracking manually (see page 14).
Picture distortion can be caused by using E300 cassettes
which were recorded with a slow tape speed (LP or EP).
You are advised not to use E300 cassettes.
The cassette is recorded in a tape speed, colour or video standard
which is not corresponding to the VCR setting.
Check which standard was used when the video cassette was recorded.
Setting of PAL or MESECAM can be adjusted manually (see page 8).
The Playback from NTSC is not possible.
The aerial cable or scart cable is not correctly connected or is defective.
Check the connections, aerial signal and cables
(replace cables if necessary).
Setting for SQPB (S-VHS Quasi Playback) is not correct.
Setting can be changed (see page 9).
The playback picture is distorted when you record the tape on EP mode
using MESECAM system. (This is not a functional fault).
We recommend PAL system for recording on EP mode.
The video heads are soiled or worn out.
Please contact service center for assistance.
Head cleaning by a service center is not covered by warranty.
Troubleshooting
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic nv fj 613 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic nv fj 613 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info