683927
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
BA 873040led N;DE,GB -23435- 2016.11V02
INSTRUCTION MANUAL DIMMER [LED STRIPES]
Technical Features Safetey instructions
Supply voltage 12 – 48 VDC*
CAUTION!! DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption 0,5 VA
Suitable type of lamps Dimmable LED lamps
Maximum load 8A
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately
No safe electrical isolation between the power supply and pushbutton 2!
When using a 230V~ pushbutton on P
L
und P
N
no low voltage protection, no SELV!
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes
Max. number of pushbuttons Unlimited (non-lighted pushbuttons)
Pushbutton 1 Pushbutton referred to Ground
Optional: Pushbutton 2 Pushbutton referred to 230V~ (no SELV)
Dimensions 46 x 42 x 13 mm
Weight 23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection IP20 according to DIN EN 60529
*NOTE: The power supply associated with this dimmer should comply with the Low Voltage Directive 2006/95/EC and EMC
Directive 2004/108/EC
Important Note
For all lamps, please take into account the specifications of the manufacturer!
Description / Installation / Operation Wiring diagram
Description / Intended use
Dimmer for LED lamps 12 - 48VDC up to 6A, with Pulse Width Modulation technology (PWM),
specially designed for 1-channel LED strips.
Small size dimmer, for flush-mounting (e.g. behind standard pushbutton).
Protected against overload and short circuit. Built-in heat protection.
Can be used with a pushbutton referred to Ground (Pushbutton 1) or a pushbutton referred to 230V~ (Pushbutton 2) or both.
When using a 230V~ pushbutton on P
L
und P
N
the low voltages are not SELV!
With or without memory function.
With two function rotary switches:
min: minimum brightness level (1% up to ~60%).
dim speed: dimming speed between 3 and 10 sec. (from 0 to 100%).
Installation
1 Disconnect installation from power supply and check that power supply is disconnected.
2 Install the dimmer according to the wiring diagram.
3 Make sure the loads are connected properly and reconnect power supply.
4 Press shortly the pushbutton to switch the lamps on and dim with a long press to the minimum brightness level.
5 If you like the change the minimum brightness level you have to disconnect the installation again from power supply and set
with the rotary switch (min) the desired minimum brightness level.
.
Operation
Press shortly the pushbutton to switch the lamps on and off!
=> Switch on „No Mem“ = Lamp(s) switches on with max. brightness.
=> Switch on „Mem“ = Lamp(s) switches on with the brightness of the last switch off
With a long press you can dim!
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Paladin 873 040 led bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Paladin 873 040 led in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info