683964
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
GB
DE
BATTERY REPLACEMENT
Release the cover of the sensor with the help of a screwdriver. Insert it into the upper slot.
Remove the cover of the socle and remove the battery being careful with the components of
the printed circuit.
The thermostat also indicates low battery status by flashing its red LED when the selection
wheel is moved. At his moment it is necessary to change the battery.
The 676311rf has a channel type CH_Battery_Status (Channel Code 0021h).
This channel allows to inform to a compatible actuator about this information.
When the battery is worned-down, the sensor will send every 15 minutes the respective
telegram and a “battery empty” message.
This function is optional. In order to link the sensor with a compatible actuator:
1.- Remove the battery from the 676311rf.
2.- Set the RF actuator in link mode, according to the instructions given by the
manufacturer.
3.- Insert the battery again in the socle.
4.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
After replacing the battery it is necessary to:
1. - Turn selection wheel to the maximum 30°C position.
2. - Turn selection wheel to OFF position.
FIRST STARTING
NOTE: pull the plastic foil of the battery out to become operative the device.
After removing the plastic foil it is necessary to:
1. - Turn selection wheel to the maximum 30°C position.
2. - Turn selection wheel to OFF position.
BATTERIETAUSCH
Um die Batterie zu tauschen, öffnen Sie die Abdeckung des Sensors mittels eines kleinen
Schraubendrehers. Entfernen Sie anschließend die rückseitige Abdeckung und ersetzen Sie
die Batterie. Hierbei sollten Sie darauf achten, die Leiterplatte nicht zu beschädigen.
Der Sensor meldet eine schwache Batterie anhand einer rot blinkenden LED während der
Verstellung des Drehwahlschalters.
Der Sensor überträgt den Batteriestatus auch per Funk (CH_BATTERY_STATUS:
Channel_Code_0021h), sofern der Empfänger diesen Status auswerten kann. Im Falle
eines niedrigen Batteriestandes wird diese Meldung alle 15 Minuten übertragen.
Um den Sensor mit einem kompatiblen Aktor zu verlinken, der diese Funktion unterstützt
gehen Sie wie folgt vor:
1.- Entfernen Sie die Batterie aus dem Sensor 676 311 rf.
2.- Empfängerkanal des gewünschten RF-(KNX)-Gerätes in den Verlinkungsmodus stellen
(gemäß den Vorgaben des Herstellers)
3.- Batterie einsetzen
4.- Erfolgreiche Verlinkung anhand des Aktors (gemäß den Vorgaben des Herstellers)
prüfen.
Nach einem Batterietausch sind folgende Schritte notwendig:
1.– Drehwahlschalter auf Position 30°C (Maximalwert) stellen.
2.– Anschließend: Drehwahlschalter auf Position “AUS” stellen.
ERSTINBETRIEBNAHME
Wichtig: Ziehen Sie die Schutzfolie der Batterie heraus um das Gerät verwenden zu
können.
Nach dem Entfernen der Schutzfolie sind folgende Schritte notwendig:
1. – Drehwahlschalter auf Position 30°C (Maximalwert) stellen.
2. – Anschließend: Drehwahlschalter auf Position “AUS” stellen.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Paladin 676 311 rf bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Paladin 676 311 rf in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info