683958
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
GB
Workingtemperature -5ºC ~ +45ºC
Radio-Frequency 868,4MHz
Range
100m (in the freefield)
~30m (inside buildings)
1-CHANNEL BLINDS/SHUTTERS ACTUATOR OR
2-CHANNELS SWITCHING ACTUATOR
TECHNICAL DATA
DESCRIPTION
Wireless actuator for switching or controlling blinds/shutters compatible with the KNX-RF
Standard.
It has 2 output channels which allow to control one blind/shutter or to use them as a two
channels switching (ON/OFF) actuator.
It has 2 auxiliary inputs which allow to control also by two wired conventional pushbuttons.
MOUNTING AND INSTALLATION
A. Mounting:
• Place the actuator with the antenna as far away as possible from wires or metallic
surfaces.
• Move away the actuator from attenuations or interferences, for example from metallic
surfaces or other radio-frequency devices.
B. INSTALLATION:
Important: Switch off the power supply when installing!
B.1.– Wiring as 1-channel blinds/shutters actuator:
To roll up or down a blind, follow the wiring diagram of Fig 1.
Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility of
controlling the load with two wired pushbuttons.
B.2.– Wiring as 2-channels switching actuator:
To control the switching ON and OFF of two diferent loads follow the wiring diagram of Fig 2.
Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility of
controlling the load with two wired pushbuttons.
COMMISSIONING
• Programming selector switch:
P1: Programming Output 1 ‘R1’ (’Double Switch’ mode) or Blinds/Shutters actuator
(’Blinds control’mode).
P2: Programming Output 2 ‘R2’ (’Double Switch’ mode) or Blinds/Shutters actuator
(’Blinds control’ mode).
F: Standard working mode without Repeating function.
Rpt.: Standard working mode with Repeating function.
Rst.: Reset.
• Working mode selector switch:
1: ‘Blinds control’ mode.
2: ‘Double Switch’ mode.
Important: Changing operation mode lasts for ~ 10sec and involves the internal Reset of
the device.
• Programming LED key: links or deletes a sensor or actuator.
Programming a link between 674 730 rf (input channel) and a RF Sensor
To program a link between the input channel of the 674730rf and a RF transmitter device
(key, remote control, motion detector, touch screen ...):
1.- Turn the programming switch to position 'P1' or 'P2’:
• P1: to link the Load 1 in ‘Double Switch’ operating mode.
• P2: to link the Load 2 in ‘Double Switch’ operating mode.
• P1 or P2: to link the loads in ‘Blind control’ operating mode.
The green LED of the ‘Prog’ key will flicker slowly.
2.- Press briefly the ‘Prog’ key. The green programming LED must light up constantly.
3.- Set the RF sensor wich is going to be linked with the 674730rf in ‘link programming
mode’ according to its manual instructions.
4.- If the link is successful the green LED of the ‘Prog’ key will flicker slowly again. In this
case, place the programming selector switch to ‘F’.
If the link fails, the LED will remain constantly ON. In this case, place the selector switch
to ‘F’ and repeat all the process from step 1.
Auxiliary inputs 2 Inputs
Channels
Blinds/Shutters: 1 channel
Switch: 2 channels
Load capacity
2 x 16A
2 x 5A cosφ=0,5
Power supply 230V~ 50Hz
M
Programming a link between 674730rf (output channel) and a RF Actuator
To program a link between the output channel of the 674730rf and a RF actuator:
1.- Set the RF actuator in ‘link programming mode’.
2.- Turn the programming switch to position 'P1' or 'P2’:
• P1: to link the Output channel RF1 in ‘Double Switch’ operating mode.
• P2: to link the Output channel RF2 in ‘Double Switch’ operating mode.
• P1 or P2: to link the loads in ‘Blind control’ operating mode.
The green LED of the ‘Prog’ key will flicker slowly.
3.- Press briefly the ‘Prog’ key. The green programming LED will continue flickering.
4.- If the link is successful the green LED of the ‘Prog’ key will continue flickering slowly. In
this case, place the programming selector switch to ‘F’.
If the link fails, the green LED will remain constantly ON. In this case, place the selector
switch to ‘F’ an repeat all the process from step 1.
Reset. Delete all links
1.- Turn the programming selector switch to ‘Rst.’. The red LED of the ‘Prog.’ key will flicker
quickly.
2.- Keep pressing the ‘Prog.’ key for more than 5sec. After this time the red LED will remain
ON for 2sec and then it will flicker quickly again.
3.- Place the programming selector switch to ‘F’.
Enabling / Disabling the Repeating function
The repeater function can be used in installations where are communication problems
between RF devices.
The 674730rf must be installed in a location that provides cover for most part or all of the
installation RF devices.
To enable this function, place the programming selector to position 'Rpt.'.
Important: It is not recommended the use of more than two repeaters in a same installation.
Also, it is not recommended to use it unless necessary.
OPERATION
Blinds/Shutters control mode (1)
Action Operation
Brief press on P1
or
Receiving RF telegram:
"Step Up"
(a) If the blind is moving, stops
(b) If the blind is stopped, goes a step up
Sends a RF telegram "Step Up" if the action has been done
from the auxiliary pushbutton P1.
Brief press on P2
or
Receiving RF telegram:
"Step Down"
(a) If the blind is moving, stops.
(b) If the blind is stopped, goes a step down.
Sends a RF telegram "Step Down" if the action has been
done from the auxiliary pushbutton P2.
Sustained press on P1
or
Receiving RF telegram:
"Move Up"
(a) If the blind is moving down, stops and changes its
movement rolling the blind up for 3 minutes
(b) If the blind is stopped, it moves up for 3minutes
(c) If the blind is moving up, it will continue for 3 minutes
more
Sends a RF telegram “Move Up” if the action has been
done from the auxiliary pushbutton P1.
Sustained press on P2
or
Receiving RF telegram:
"Move Down"
(a) If the blind is moving up, stops and changes its
movement rolling the blind down for 3 minutes
(b) If the blind is stopped, it moves down for 3 minutes
(c) If the blind is moving down, it will continue for 3 minutes
more
Sends a RF telegram “Move Down” if the action has been
done from the auxiliary pushbutton P2.
Double Switch mode (2)
Action Operation
Brief or sustained press on
P1
(a) If the Load 1 is OFF, it switches ON and sends the RF
telegram “ON” (RF output channel1)
(b) If the Load 1 is ON, it switches OFF and sends the RF
telegram “OFF” (RF output channel1)
Receiving RF telegram in the
channel 1: “ON”
Switch ON Load 1
Receiving RF telegram in the
channel 1: “OFF”
Switch OFF Load 1
Brief or sustained press on
P2
(a) If the Load 1 is OFF, it switches ON and sends the RF
telegram “ON” (RF output channel 2)
(b) If the Load 1 is ON, it switches OFF and sends the RF
telegram “OFF” (RF output channel 2)
Receiving RF telegram in the
channel 2: “ON”
Switch ON Load 2
Receiving RF telegram in the
channel 2: “OFF”
Switch OFF Load 2
Fig. 3
Fig. 2
674 730 rf
L
N
M
P1
P2
L
N
P1
P2
C1
C2
Fig. 1
674 730 rf
674 730 rf
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Paladin 674 730 rf bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Paladin 674 730 rf in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info