606573
3
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
B: Parts list for product: OF698
Before tting, check that the following parts are included in the kit:
• 1 x Left HotGrip (22mm I/D x 125mm long )
• 1 x Right HotGrip (25.6mm I/D x 125mm long)
• 1 x Rainproof Panel mounted Switch rated to IP56
• 1 x Wiring loom with battery ring leads, 5amp quick-blow glass fuse, cable ties and grip superglue
• 1 x Oxford Hotgrip instructions
• 1 x Flat drill bit (20mm)
Tools needed:
A course and ne le for smoothing the throttle slider tube etc.
Glass paper for cleaning the handlebars
Cable snippers or pliers
Standard motorcycle tools to remove the seat, fairing panels and battery connections
• Power Drill
C: Fitting and Wiring Instructions
Your Oxford HotGrips are designed as a replacement for the handle bar grips already tted to the motorcycle.
Hotgrips will t onto most motorcycles that use 22mm or 7/8” Ø handlebars. The grip has an open end to al-
low for the bar end weight to be re tted without the need to trim the grip. If the end of the Hotgrip does need
to be trimmed to ensure that a bar-end weight can be tted without fouling the Hotgrips, then it is advisable to
trim up-to the point show in the diagram below. This ensures that the heating elements do not get cut.
If you do not wish to cut the grip, it might be possible to put a metal washer or spacer on the inside of the
bar-end weight to give additional clearance.
The left and right grip are different sizes:
One is designed to t over the left handlebar and has an internal diameter of approximately 22mm. The other
ts over the throttle slider on the right handlebar and has a diameter of approximately 25mm.
D: Fitting Procedure
1. Remove the existing handlebar grips.
2. Clean the left handlebar ensuring that the bars are smooth and free of glue and residue.
3. The bar should measure a consistent 22mm diameter.
4. If the HotGrips do not slide on easily, check if there is any excess rubber on the inside of the grip
which may have seeped through the expansion slot during manufacturing. If so, use a long le
and gently remove the excess rubber with the edge of the le.
5. When the right grip is removed there is a nylon throttle slider underneath. This may need to be
removed and any raised areas smoothed off to ensure that the diameter is a consistent 25.6mm.
This often involves ling off the raised ridges that were formed on the throttle slider.
Oxford Hotgrips Light instructions v.1 7/9/10 3
Can be trimmed
to this point
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Oxford OF698 HotGrips Light bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Oxford OF698 HotGrips Light in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 2,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info