668497
19
Verklein
Vergroot
Pagina terug
1/51
Pagina verder
19
6.2 Programming the chairlift
Start programming procedure when ‘potentiometer’ speed is set.
Programming procedure:
1 Switch on Service.
2 Move the chairlift to the left by operating Left (servicebox), until it stopped against the buffer
3 Release Left
4 Switch off Service.
5 Choose speed 1 or 2 (switch 1 2) speed should be set before programming procedure
6 Switch on Teach
7 Operate Right (on servicebox) (the chairlift begins to move).
Keep Right operated till point 10.
8 If necessary, switch over the speed by operating switch 1 2.
(Max of 35 times of switch over in speed possible)
9 If the chairlift has stopped against the other buffer, the system beeps 5 times.
10 Release Right
11 Switch off Teach
12 Remove the connector from the service box if there are no additional charging points.
If an extra charge point has been installed on the rail, the chair can be programmed in for this.
Programming procedure for extra charge-point(s)
13 Switch on Service
14 Move the chairlift to the extra charging point.
15 Park the chairlift exactly in the middle of the charging point.
16 Leave the system on Service and switch on Teach mode, the system will beep once.
17 Switch off Teach.
18 Switch off Service.
19 Remove the plug from the service box.
If a second extra charging point has been installed, this can be programmed into the chairlift as well.
Repeat points 13 through 19, the system will beep twice at point 16. (3th charging-point 3 times...etc.)
In total 5 extra charging points/stoppoints can be added.
Extra charging-points can not be deleted.
When a incorrect charging-point has been programmed in, start at point 1.
You can choose for which control the chairlift should stop on the extra charging point(s)
Dipswitch 4 = on, the lift will stop when operated on by the remote-control.
Dipswitch 5 = on, the lift will stop when operated on the armrest.
Dipswitch 4 + 5 = on, the lift will stop when operated by the remote-control as well as on the armrest.
6.3 Activate alarm signal when controlled by remote
Alarm during movement when controlled by remote can be activated or de-activated by controlling
L+R 1sec on the servicebox. (Service and/ or Teach should be in off position)
This functionality is added in software version d32 or higher.
Only start programming the lift, when the lift is operating OK (without bypass-connector.)
The sensors need to be calibrated first and the Tilt sensor should be adjusted first. (see 5.4 / 5.5)
Both displays should show a ‘1’ in the display.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Otolift-One

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Otolift One bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Otolift One in de taal/talen: Engels als bijlage per email.

De handleiding is 4,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info