586205
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Easy installation
Generally, once the receiver is switched on, it is ready to play channels from default channel list.
If after turning on You can see only receiver’s menu, and when You try to push MENU or EXIT button, “No channels!”
information appears, it means that channel list has been erased. There are two ways to create new channel list:
Restore default channel list, or
Scan Your own channel list
Restore default channel list
To restore default channel list, explore the menu with / buttons, and select Tools menu. Press OK to enter. You
may be asked about password (default is 0000 enter using numeric buttons). Using / buttons select Factory
Setting option and press OK. Use /buttons to move cursor to “Yes“ and again confirm by OK button. After a while,
reboot receiver using POWER button.
If after above settings, channels are still not played, only “No Signal!” information appears on screen, go to next
chapter, where You can find how to configure Your satellite installation.
Configure Your satellite installation
To configure satellite installation, explore the menu with / buttons, and select Installation menu. Press OK to
enter. You may be asked about password (default is 0000 enter using numeric buttons). Using / buttons select
Antenna Connection and press OK. This menu contain only one function LNB. Using / buttons, You can select
what kind of antenna installation is connected to receiver fixed (in most situations) or motor (special dish positioning
system for this installation, refer to motor instruction manual). Select Your installation type and press MENU to back
to Installation.
Now using / buttons select Satellite List and press OK. In this menu, using / and OK buttons You can define
which satellites are available in Your installation. Next, press MENU to back to Installation.
If Your installation receive signal from more than one satellite, use / buttons to select Antenna Setup and press
OK. In satellite function use / buttons to choose satellite and in DiSEqC1.0 function You can assign selected
satellite to corresponding DiSEqC switch input. Use MENU to back to Installation. Now Your satellite installation should
be finally configured and ready to receive connected signal.
Scan Your own channel list
After satellite installation configure, You can create Your own channel list.
If You want to erase all currently existing channels, explore the menu with / buttons, and select Edit Channel
menu. Press OK to enter. You may be asked about password (default is 0000 enter using numeric buttons). Using
/ buttons select Delete All and press OK. Use /buttons to move cursor to “Yes“ and again confirm by OK
button. After a while, channel list will be empty.
Now, explore the menu with / buttons, and select Installation menu. Press OK to enter. You may be asked about
password (default is 0000 enter using numeric buttons). Using / buttons select Multi Satellite Search and press
OK. Next, using / buttons select Search and press OK. Receiver start scanning all selected previously in Satellite
List function satellites. Please, be noted his procedure may takes few minutes.
If after above procedures, Your receiver still cannot play channels, it is highly recommended to contact with Your local
professional installator or seller.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Opticum FS 10p bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Opticum FS 10p in de taal/talen: Engels als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Opticum FS 10p

Opticum FS 10p Snelstart handleiding - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info