651591
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Instructions for Machine Transport
NOTE: Refrigerated equipment must remain upright to avoid damage to the compressor.
In order to prevent the oil contained in the compressor from flowing into the cooling system, it is
necessary to always ship, carry, store and handle this drink dispenser in an upright position, fol-
lowing the instructions located on the packaging. Never ship, carry, store or handle this unit on
its side.
1.1 RECEIVING
Each unit is completely tested under operating conditions and thoroughly inspected before
shipment. At the time of shipment, the carrier is responsible for the unit and any claim for dam-
age must be made with the carrier. Upon receiving units from the delivering carrier, carefully in-
spect the carton for visible indication(s) of damage. If damage exists, have carrier note same
on bill of lading and file a claim with the carrier.
1.2 UNPACKING
A. Cut band and remove.
B. Carefully remove top portion of carton by lifting up, see figure 1.
C. Remove top inner carton pad from inside of packing box.
D. Inspect unit for concealed damage and if evident, notify delivering carrier and file
a claim against same.
Installation Positioning the machine
The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides and back of
the machine to allow proper ventilation. Installation of the machine near a heat source
should be avoided. Some heat sources you should avoid locating this unit too close to are
ovens, coffee machines, cold or frozen beverage dispensers or ice machines (equipment with
compressors that expel hot air through its vents). A room temperature between 5F (15°C)
and 7F (25°C) is recommended.
Connection to Main Power Supply
• The electrical safety of this drink dispenser can only be achieved if the machine is properly
connected to an appropriate grounded receptacle that is in compliance with current national
safety standards. Therefore, the manufacturer cannot be held responsible for damage and/or
injury caused by failure to connect the unit to an appropriate source of power.
• For a safe and correct installation, connect the unit to a dedicated outlet.
• Do not alter the cord or plug in any way.
• The entire length of the power supply cord must not, in any way, be compressed, bent, or
bunched together, nor may extension cords be used.
• Do not obstruct the ventilation vents on the side and rear panels of the unit. Insufficient venti-
lation will reduce the efficiency of the machine, causing it to function inadequately, and can
cause serious damage. A minimum of eight inches (20cm) clearance is necessary on each side
and behind the unit.
WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE FATAL
ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR. THE POWER CORD IS PROVIDED WITH
A THREE PRONG GROUNDED PLUG. IF A THREE-HOLE GROUNDED ELECTRICAL OUTLET IS NOT
AVAILABLE, USE AN APPROVED METHOD TO GROUND THE UNIT. DO NOT USE EXTENSION CORDS
WITH THIS UNIT. DO NOT GANG TOGETHER WITH OTHER ELECTRICAL DEVICES ON THE
SAME OUTLET.
4
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Omega OSD10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Omega OSD10 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info