Handleiding Oceanic VTX (pagina 13 van 64) (Engels)

664356

Verklein

Vergroot

Pagina terug

1/64

Pagina verder

VTX OPERATING MANUAL

SET AUTO DIM

TIM E U N TIL DI M

OFF

D I M TO B R IG H TNE S S

30 %

SET AUTO DIM

TIM E U N TIL DI M

0:3 0 M IN: S EC

D I M TO B R IG H TNE S S

30 %

SETUP MENU

SET DATE , TIM E

BAT T, TMT STAT US

BLUETOOTH

SET AU TO D I M

Fig. 15 - HOME SETUP

HOME SETUP MENU, selections include (Fig. 15):

> SET AUTO DIM - select to access the Set Auto Dim feature.

> SET DATE, TIME - select to access the Set Date, Time Menu.

> BATT, TMT STATUS - select to activate the VTX' receiver then view status information for the VTX and Transmitters.

> BLUETOOTH - select to initialize the Bluetooth function.

• A (< 2 sec) - to step forward (down) through the Menu selections.

• M (< 2 sec) - to step back (up) through the selections.

• S (< 2 sec) - to access the highlighted selection.

• S (2 sec) - to revert to the Home Menu.

SET AUTO DIM,

selections with the last settings saved include (Fig. 16A/B):

This feature will allow you to set a time that Dive Main screens will remain illuminated (after the last button press) at the Brightness

% level you adjusted it to before it is reduced to the Dim level that you set it to here.

> TIME UNTIL DIM with the graphic OFF, or 0:30 MIN:SEC, ﬂashing.

> DIM TO BRIGHTNESS with 30 %.

• A (hold) - to scroll upward through Time set points 8/sec from OFF to 0:20 through 2:00 MIN:SEC in increments of 10

seconds (0:10).

• A (< 2 sec) - to step upward through the Time set points one at a time.

• M (< 2 sec) - to step back through the Time set points one at a time.

• S (< 2 sec) - to save the Time setting.

If OFF is selected, the Dim To Brightness setting is to be bypassed with operation reverting to the Home Setup Menu. The

Auto Dim feature is to be disabled and have no affect during dives.

If a min:sec Time value is saved, it is to become solid and Dim To Brightness % is to be highlighted and ﬂash.

• S (2 sec) - to step back to the Setup Menu without saving the setting.

• A (< 2 sec) - to step upward through the % Dim set points from 10 through 60% in increments of 10% one at a time.

• M (< 2 sec) - to step back through the % set points one at a time.

• S (< 2 sec) - to save the setting,

which is to become solid with the highlight removed, and revert to the Home Setup Menu

with the Set Auto Dim selection highlighted allowing other operations

• S (2 sec) - to step back to Set Time without saving the setting.

SET DATE, TIME MENU, selections with the last settings saved include Fig. 17):

> DATE FORMAT = with M.D (for Month.Day) or D.M (for Day.Month).

> DATE = with Month.Day.Year or Day.Month.Year, based on the Date Format.

Set Year, then Month, then Day.

> HOUR FORMAT = with 12 (12: Am to 11: Pm) or 24 ( 0: to 23:).

> TIME = with hr:min (

12:01 A to 11:59 P, if 12 Hour Format; or 0:01 to 23:59, if 24 Hour Format).

Set Year, then Minute.

• A (< 2 sec) - to step forward (down) through selections.

• M (< 2 sec) - to step back (up) through selections.

• S (< 2 sec), when a selection is highlighted - to highlight and ﬂash that item's set point (see below).

• A (< 2 sec) - to toggle or increase set points one at a time.

• A (hold) - to increase set points at a rate of 8 per second.

• M (< 2 sec) - to toggle or decrease set points one at a time.

• S (< 2 sec) - to save the setting which becomes solid, with the selection ﬂashing.

• S (2 sec) - to revert to the Setup Menu.

BATTERY/TMT (TRANSMITTER) STATUS, information includes (Fig. 18):

Also refer to page 8.

> VTX = BATT GOOD (or LOW)

> TMT 1 = BATT GOOD (or LOW), or NOT AVAIL, or OFF

> TMT 2 = BATT GOOD (or LOW), or NOT AVAIL, or OFF

> TMT 3 = BATT GOOD (or LOW), or NOT AVAIL, or OFF

> TMT 4 = BATT GOOD (or LOW), or NOT AVAIL, or OFF

GOOD (green) means that battery power is acceptable (=> 2.75 volts).

LOW (yellow) means that the battery should be changed (< 2.75 volts, warning level).

LOW (red, ﬂashing) means that the battery must be charged prior to further operations (< 2.50 volts, alarm level).

NOT AVAIL means that the VTX's receiver is not receiving that Transmitter's signal.

OFF means that the Transmitter has not been selected for use.

• S (2 sec) - to revert to the Setup Menu.

• 10 sec - revert to the Setup Menu if S is not pressed.

DATE F OR M AT = M.D

HOU R F O RMAT = 12

DATE = 7 . 24. 1 4

SET DATE, TIME

TIM E = 10:3 8 A

Fig. 17 - SET DATE, TIME

Fig. 18 - BATTERY/TMT

STATUS

BATT, TMT STATUS

V T X =

TMT

1 =

TMT 2 =

TMT 3 =

TMT

4 =

BAT T G O OD

NOT AVA IL

BAT T LO W

OFF

BAT T G O OD

Fig. 16A - SET AUTO DIM

Fig. 16B - SET AUTO DIM

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Oceanic VTX Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info