47387
24
Verklein
Vergroot
Pagina terug
1/25
Pagina verder
COMMAND CENTER
23
7 Troubleshooting
If trouble occurs with COMMAND CENTER, carry out the applicable checkpoints and
procedures indicated on the following pages. If the trouble persists, contact your service
representative or authorized service center.
Trouble Check point Procedure Reference
Page
I can’t access COMMAND
CENTER.
Is the power turned on to this
machine?
Turn the power on to this machine,
wait until it is a ready state and try
to access COMMAND CENTER.
-
Is the network cable properly
connected?
Connect the network cable
properly.
-
Are the network settings that are
made in this machine correct?
Perform the network settings from
the operation panel. Contact your
network administrator for
information on the appropriate
settings.
-
Is the IP address for this
machine entered correctly?
Enter the correct IP address.
Check with your network
administrator to make sure the
correct IP address has been
designated for this machine.
-
Are the LAN settings that are
made in your browser
application correct?
Check the settings made in your
browser application. For details,
refer to the Help function, etc. in
your browser application.
-
Has the administrator set up an
IP Filter function?
Access COMMAND CENTER
from an approved IP address.
15
The SNMP Read Community
settings function as passwords
to control read and write access
to the device via SNMP.
Access COMMAND CENTER
from an approved Read
Community.
18
Does the version of your
browser application support
operation using COMMAND
CENTER?
Use a browser application that
supports operation using
COMMAND CENTER.
3
Characters do not display
properly in COMMAND
CENTER.
Does the version of your
browser application support
operation using COMMAND
CENTER?
Use a browser application that
supports operation using
COMMAND CENTER.
3
I can’t access the Basic,
Printer, and Advanced pages.
Has the administrator set a
password?
Enter the appropriate password. -
I can’t perform settings. Is the printer currently in
operation?
Settings are not possible while the
machine is currently printing. Wait
until the operation has been
completed.
-
The settings I made are not
registered.
Did you click on the Submit
button after making the
settings?
After you make the desired
settings, click on the Submit
button and move to another page
or close COMMAND CENTER
window.
10
Did you click on the Restart
button after making the network
settings? Network settings are
not registered until the machine
is restarted.
Restart this machine. All settings
will be registered.
12
The administrator has forgotten
the Admin password.
- If the Admin password is
forgotten, reset to factory defaults.
12
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Oce OP1025 Operation Guide Command Center bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Oce OP1025 Operation Guide Command Center in de taal/talen: Engels als bijlage per email.

De handleiding is 1,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info