677276
5
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
5
OPERATION
Turn off the system first, turn down the receivers volume to the minimum and then turn on the receiver, CPU initializes, the LCD
screen begins to display and the system reverts to the last shutdown’s state!
If the system is turned on look at the transmitter and receiver’s frequency.Then the receiver display shows RF signal level value,
the antenna status will display antenna A or B. Adjust the volume to the desired level.
Volume adjustment
Adjust the receiver’s volume to the 12 o’clock position, then adjust the volume of the amplifier or mixer to a desired level. If the
receiver volume has been adjusted too loud the amplifier will produce a saturated distortion which will blow the amplifier or/and
the loudspeaker(s)!
Best acoustics:
1. You should always see the receiver antenna from your transmitter location.
2. The distance between transmitter and receiver should be as short as possible.
3. If the receiver has two antennas, they should be adjusted 45° with a vertical line.
4. Keep the antennas away from metal surfaces and shelter.
5. Let the antennas not contact or cross each other.
6. Before using the system during the presence of public do a test to find out where the “dead spots” are. Avoid these
spots when operational
TROUBLESHOOTING
PROBLEM
INDICATOR
SOLUTION
No sound
Red transmitter indicator is not flash
Slide transmitter POWER ON/OFF
switch to ON position. Make sure battery
is inserted properly, observing battery (+
/ -). If battery is inserted properly,
replace with fresh battery.
No sound
Red transmitter indicator is flash.
Slide transmitter MUTE/ON switch to
ON position.
No sound
Red receiver indicator POWER light off.
Make sure AC adapter is securely
plugged into electrical outlet and into DC
input connector.
Make sure AC electrical outlet works
and supplies proper voltage.
No sound
Receiver signal indicators A/B lights
glowing.
Turn up receiver volume control.
Confirm that the output connections
from the receiver to the external
equipment are secure.
Sound level differs from level of a
cabled instrument.
Receiver signal indicators A/B lights
glowing.
Adjust transmitter gain level to
compessary.
Adjust receiver volume as necessary.
Distortion level increases gradually
Receiver signal indicators A/B lights and
transmitter LOW BATTERY light
glowing
Replace transmitter battery
Bursts of noise or other audible
radio signals present.
Signal indicators A/B/ lights on.
Identify potential sources of
interferences (other RF-sources) and
turn off, remove or use a wireless
system operating on a different
frequency.
Momentary loss of sound as
transmitter is moved around
performing area.
Receiver signal indicator A/B lights of
when sound is lost
Reposition receiver and perform walk-
through test again. If audio dropouts
persist, mark “dead” spots and avoid
them during performance.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ONYX STWM711 - 179.185 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ONYX STWM711 - 179.185 in de taal/talen: Nederlands, Duits, Engels, Spaans als bijlage per email.

De handleiding is 0,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info