665704
7
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
12
DITEC S.P.A - IP1580 30/06/99 - CS61/CS61E
1. TECHNICAL DATA
Power supply 230 V~ 50 Hz
Absorption 2 A
Motor power 250 W
Torque 700 N
Max. run 13 m
Max. door weight 600 kg
Speed 0.18 m/s
Intermittence S2 = 15 min. / S3 = 25%
Temperature -15 °C / +50 °C
Degree of protection IP54
Weight 12.7 kg
2. REFERENCE TO ILLUSTRATIONS
2.1 Standard installation references (fig. 1)
ATTENTION: Only use DITEC’s safety devices and accessories for installation.
1 Radio
2 Flashing light
3 Key selector
4 Connect power supply to an omni-pole switch with a contact opening gap of no less that 3 mm (not supplied
by us)
2.2 Geared motor references (fig. 2)
9 Geared motor
10 Carter
11 Release access door
12 Release
3. INSTALLATION
3.1 Preliminary checks
Check for gate stability and that the slide wheels are in good condition and the top guides do not cause any
friction. The slideway must be securely anchored to the ground and fully exposed along its full length. It must be
perfectly smooth so as to avoid jamming of the gate.
Provide an opening and closing stop.
Make sure that the gate is securely inserted in the slideway so that it cannot come out of the
slideway and fall.
Geared motor installation
Unless otherwise specified, all measurements are expressed in millimetres.
3.2 (Fig. 4) Lay a concrete foundation with buried anchoring brackets and the base plate, making sure that it is
pefectly level and smooth. Allow for 80 mm between the plate axis and the rack B . Route the cable ducts
through the two holes in the middle of the plate.
3.3 (Fig. 5) Open the release access door 11 , loosen the screw that locks the carter and lift it. Insert the
ancoring feet G at the gear motor base. Position the geared motor on to the base plate. Adjusting
gearmotor: horizontally by sliding in the ancoring feet notches, vertically with the 4 levelling screws D :
while adjusting vertically, keep the motor slightly raised above the base plate so as to allow enough
space to secure the rack and to make any subsequent adjustments, if necessary.
3.4 (Fig. 6) Secure the rack by disengaging the geared motor and opening the gate. Place the rack on pinion
15 and move the gate manually to secure the rack along its full length. Once the rack has been secured,
vertically adjust the geared motor so as to have a gap of 2 to 3 mm between the pinion and the rack. Finally,
firmly secure the geared motor by fitting shims E and washers F .
3.5 (Fig. 7, 8) Adjusting limit switch: secure the limit stop skids H on to the rack so that the gate stops about
20 mm before reaching the stop.
ENGLISH
5 Geared motor + Electrical board
6 Photocells
7 Rubber hip / Sensitive hip
8 Opening and closing stop
13 Electrical board
14 Limit-switch spring
15 Pinion
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novotecnica CS 61 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novotecnica CS 61 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info