609460
85
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
USER MANUAL
ENGLISH
9098960000(1)2011-04 A SCRUBTEC R 466 - R 471 - R 471C - BOOST
®
R4 23
SQUEEGEE CLEANING
NOTE
The squeegee must be clean and its blades must be in good conditions in order to get a good drying.
CAUTION!
It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.
Drive the machine on a level oor.1.
Insert the ignition key (58) and turn it to “I”.2.
Lower the squeegee (30) with the switch (65).3.
Turn the ignition key (58) to “0”.4.
Disconnect the vacuum hose (31) from the squeegee.5.
Loosen the handwheels (34) and remove the squeegee (30).6.
Wash and clean the squeegee. In particular, clean the compartments (A, Fig. 7) and the vacuum hole (B). Check that the front 7.
blade (C) and the rear blade (D) are integral and free from cuts and lacerations; if necessary replace them.
Assemble in the reverse order of disassembly.8.
SQUEEGEE BLADE CHECK AND REPLACEMENT
Clean the squeegee (Fig. 7) as shown in the previous paragraph.1.
Check that the edge (E) of the front blade (C) and the edge (F) of the rear blade (D) lay down on the same level, along their 2.
length; otherwise adjust their height according to the following procedure:
Remove the tie rod (G), disengage the fastener (M) and adjust the rear blade (D); then engage the fastener and install the
tie rod.
Loosen the handwheels (I) and adjust the front blade (C); then tighten the handwheels.
Check the front blade (C) and rear blade (D) for integrity, cuts and tears; if necessary replace them as shown below. Check 3.
that the front corner (J) of the rear blade is not worn; otherwise, overturn the blade to replace the worn corner with an integral
one. If the other corners are worn too, replace the blade according to the following procedure:
Remove the tie rod (G), disengage the fastener (M) and remove the retaining strip (K), then replace/overturn the rear blade
(D).
Install the blade in the reverse order of removal.
Unscrew the handwheels (I) and remove the retaining strip (L), then replace the front blade (C).
Install the blade in the reverse order of removal.
After the blade replacement (or overturning), adjust the height as shown in the previous step.
Connect the vacuum hose (31) to the squeegee.4.
Install the squeegee (30) and screw down the handwheels (34).5.
If necessary, adjust the squeegee balance adjusting handwheel (35).6.
A
C
D
B
A
I
K
F
J
E
D
C
L
I
M
G
I
Figure 7
P100441
9098960000(1)2011-04 A.indb 239098960000(1)2011-04 A.indb 23 07/04/2011 15:59:2207/04/2011 15:59:22
85

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nilfisk-ALTO SCRUBTEC R 466 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nilfisk-ALTO SCRUBTEC R 466 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info