570911
44
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
- 44 -
Troubleshooting
Troubleshooting
If you should encounter problems with your scanner, check the
following before contacting your retailer or Nikon representa-
tive. If the problems occurred during scanning, you may wish to
refer to the software reference manual for advice on trouble-
shooting scanning problems.
Problem: the status LED does not light
Checklist
Is the power switch set to ON?
The scanner is on when the end of the power switch labeled
“1” is down. See the Fast Track Guide or the “Using the
Scanner” section of this manual.
Is the power cable properly connected at both ends?
After making sure that the scanner and any devices to which
it is connected are switched off, connect the power cable as
described in the Fast Track Guide or the “Setup” section of
this manual.
Problem: the scanner will not scan
Scanning problems are often related to a problem in the SCSI
connection or to improperly installed software. In rare situations,
there may be a problem with the system itself, in which case a
complete reinstall of the operating system may be necessary.
SCSI checklist
Before checking the items listed below, make sure that the
scanner and any devices to which it is connected are off.
Is the SCSI cable loose or not connected?
Check the SCSI cabling to be sure that the cable is firmly
connected to the connectors.
Are both ends of the SCSI chain terminated?
If the SCSI chain is not properly terminated, you will experi-
ence intermittent problems with all SCSI devices. The chain
must be terminated at both ends: if you have a IBM PC/AT
compatible with a SCSI expansion board and no internal
SCSI devices, check that the board is terminated (refer to
the manufacturer’s manual). If you are using an IBM PC/AT
compatible with a SCSI expansion board and internal SCSI
devices, remove termination from the board and terminate
the last internal device in the chain. If the scanner is con-
nected at the end of the chain, set the terminator switch to
ON. If the scanner is connected between other SCSI de-
vices, terminate the last device in the chain and set the
terminator switch on the scanner to OFF. If there is an
unused SCSI connector at the end of the chain, place an
independent terminator on this connector even if the device
is connected to the chain using a through terminator. See
Setup” in this manual.
Does the cabling total more than six meters in length?
For a reliable connection, SCSI cabling should be as short as
possible. Use short, high-impedance cables.
Is the scanner’s ID the same as that of another SCSI device?
Each SCSI device must have a unique ID. Set the scanner’s
ID to a number not used by any other devices in the chain.
Remember that the computer is assigned an ID, usually “0”
or “7,” while internal hard disks often have IDs of “0” or “1.”
In the case of Macintosh computers, the host computer has
an ID of “7” while “0” and “3” may be assigned to an inter-
nal hard disk or CD-ROM drive.
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nikon COOLSCAN III LS-30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nikon COOLSCAN III LS-30 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Nikon COOLSCAN III LS-30

Nikon COOLSCAN III LS-30 Gebruiksaanwijzing - Nederlands - 49 pagina's

Nikon COOLSCAN III LS-30 Gebruiksaanwijzing - Deutsch - 49 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info