619013
8
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@Niko.be — www.niko.be PMXXX-78100R08171
XXX-78100 SENSOR (XX-781)
1,50m
Todecreasethedaytemperaturelevelortoincreasethenighttemperaturelevel,proceedasfollows:
Step Action Result
1
Press
or tillthestandarddayornighttemperature.
Dayornighttemperatureisdisplayed.
2
Brieflyrelease
or .
Dayornighttemperatureblinks.
3
Press
or till the desired temperature.
Desiredtemperatureisdisplayed.
4
Press
to confirm.
Return to starting screen, the current
temperatureisdisplayed.
B. Switching from manual to automatic mode
Aslongasahandsymbolisblinkingonthedisplay,theclockthermostatisinmanualmode.Themanualmode
willbeswitchedoffwhenacontrolcommandiscarriedout.Toswitchfromthemanualmodetotheautomatic
mode, proceed as follows:
Step Action Result
1
Press
or tillthestandardday,nightor
antifreeze temperature.
Day,nightorantifreezetemperatureisdisplayed.
2
Brieflyrelease
or .
Day,nightorantifreezetemperatureblinks.
3
Press
to switch to automatic mode.
Returntostartingscreen,handsymboldissapears.
C. Setting day or week programs
Thememorylocationsbelowarethestandardsettings.
Program Time temperature level Temperature Day RP
01 07h00 Day 20°C 1234567 1
02 23h00 Night 15°C 1234567 1
Thefactorysetprogramsetsthedaytemperatureat07h00andthenighttemperatureat23h00.Youcan,
however,setupanindividualprogramthatisadaptedtoyourpersonalrhythm.Forthispurpose,theunithas
24memorylocations.Eachmemorylocationcontainstheelements‘switchtime’,‘weekday’/’weekblock’and
‘temperaturelevel’.
Adding a switch command
Step Action Result
1
Press for 3s
to enter programming mode.
Theunitdisplaysthefirstmemorylocation(01).
2
Brieflypress
tosetweekday/block.
Theorderisasfollows:
-‘fullweek’blockMo.-Sun.(1234567)
-‘longworkingweek’blockMo.-Sat.(123456)
-‘shortworkingweek’blockMo.-Fri.(12345)
-‘longweekend’blockFri./Sun.(567)
-‘shortweekend’blockSat.-Sun.(67)
-individualweekdaysMo.,Tue.etc.…(1,2,3,4,5,6,7)
3
Press
or .
Increase/decrease switching time.
4
Press
toselectday,nightorantifreezing
temperature.
Sun,moonoricecrystalappearsontheleftsideofthe
display.
5
Press
.
Thenextmemorylocationiscalledup.
6
Press
.
Return to starting screen
Remark:whenthememorylocationafterafreememorylocationisselected,the numberoffreememory
locationsappearsonthedisplay,e.g.:rE21=21freememorylocations.
Modifying a switch command
Step Action Result
1
Press for 3s
to enter programming mode.
Theunitdisplaysthefirstmemorylocation(01).
2
Brieflypress
untilthedesiredmemory
location is selected.
Thememorylocationtobechanged,isselected.
3
Brieflypress
tosetweekdayorweek-
block.
Theorderisasfollows:
-‘fullweek’blockMo.-Sun.(1234567)
-‘longworkingweek’blockMo.-Sat.(123456)
-‘shortworkingweek’blockMo.-Fri.(12345)
-‘longweekend’blockFri./Sun.(567)
-‘shortweekend’blockSat.-Sun.(67)
-individualweekdaysMo.,Tue.etc.…(1,2,3,4,5,6,7)
4
Press
or .
Increase/decrease switching time.
5
Press
toselectday,nightorantifreezing
temperature.
Sun,moonoricecrystalappearsontheleftsideofthe
display.
6
Press
.
Return to starting screen
Deleting a switch command
Step Action Result
1
Press for 3s
to enter programming mode.
Theunitdisplaysthefirstmemorylocation(01).
2
Brieflypress
until the desired program is
selected.
Thememorylocationtoberemovedisselected.
3
Press
and simultaneously.
Contentoftheselectedmemorylocationisremoved.
4
Press
.
Return to starting screen
Deleting all settings and returning to fabric settings
Todeletealltheprogramsandsettingscarriedoutbytheuser:
Action Result
Keep
pressedandbrieflypress .
All programs and settings will be deleted. Return to fabric settings.
D. Functions with external switch
In combination with an actor, allowing for an external switch, connected on E1, the switch will have following
function:
•switchOFF:normaloperation
•switchON:nighttemperaturelevelactive(handsymbolvisible)
Attention:foraslongastheswitchisatON,thenighttemperaturewillremainactive!Inthismodethether-
mostatcanonlybeprogrammedorreset.
7. CAUTION DURING OPERATION
•Incaseoftroubles,usetheRESETbutton.Theprogramremainsinmemory.
•After±10min,astabletemperatureisdisplayed.Thisphenomenonisperfectlynormal,itdoesn’tindicatea
defect.
•Theclockthermostatcannotnotbeusedtodirectlycontrolaliquidfuelburner.Theclockthermostatisused
to activate the circulation pump for the central heating.
•Many factors could influence a temperature measurement.In order to guarantee a correct temperature
measurement, the following must be taken into account:
- Do not place the thermostat on a wall that is in direct contact with the outside air.
- Donotplacethethermostatintheimmediatevicinityofaheatingsource(stove,heating,…)oranelectrical
devicethatradiatesheat(TV,computer,…).
- Do not place the thermostat in direct sunlight or artificial light.
- Donotplacethethermostatbehindacurtainordrapery.
- Avoidaircirculationinthepipesoftheheatinginstallation.FillpossibleholeswithPU-foam.
XXX-78100
8. TROUBLESHOOTING
The‘flame’symbolisshownonthedisplay,evenifthetemperatureintheroomhasalreadybeenreached.The
thermostat is provided with a digital control and anticipates temperature fluctuations. As the pump needs some
time to heat the room, the thermostat controls the pump in advance and remains active for some time after
thesettemperaturehasbeenreached.Thisenablestohaveasteadytemperature,whichresultsinmaximum
return and minimum consumption.
9. LEGAL WARNINGS
-Readthecompletemanualbeforeattemptinginstallationandactivatingthesystem.
-Theinstallationhastobecarriedoutbyaregisteredinstallerandincompliancewiththestatutoryregulations.
-Thisusermanualhastobehandedovertotheuser.Ithastobeincludedintheelectricalinstallationfileand
hastobepassedontoanynewowners.AdditionalcopiesareavailableontheNikowebsiteorviathesupport
service.
- During installation, the following has to be taken into account (not limited to list below):
-Thestatutorylaws,standardsandregulations;
-Thestateofthearttechniqueatthemomentofinstallation;
-Thisusermanual,whichmustbereadwithinthescopeofeachspecificinstallation,onlystatesgeneral
regulations;
-Therulesofproperworkmanship
-Incaseofquestions,youcanconsultNiko’ssupportserviceorcontactaregisteredcontrolorganisation.
Support Belgium: Support UK:
+32 3 778 90 80 +44 1525877707
website : http://www.niko.be http://www.nikouk.com
e-mail: support@niko.be sales@nikouk.com
Incaseofadefect,youcanreturnyourproducttoaregisteredNikowholesaler,togetherwithacleardescription
ofyourcomplaint(Conditionsofuse,stateddefect…).
10. GUARANTEE PROVISIONS
-Periodofguarantee:2yearsfromdateofdelivery.Thedeliverydateistheinvoicedateofpurchaseofthe
productbytheconsumer.Ifthereisnoinvoice,thedateofproductionapplies.
-TheconsumerisobligedtoinformNikoinwritingaboutthedefect,withintwomonthsafterstatingthe
defect.
-Incaseofafailuretoconform,theconsumerhastherighttoarepairorreplacement(decidedbyNiko)freeof
charge.
- Niko cannot be held liable for a defect or damage as a result of an incorrect installation, improper or careless
use or wrong usage or transformation of the goods.
-Thecompulsoryregulationsofthenationallegislationconcerningthesalesofconsumergoodsandtheprotection
oftheconsumersinthecountrieswhereNikosells,directlyorviasisterordaughtercompanies,chainstores,
distributors,agentsorpermanentsalesrepresentatives,takepriorityovertherulesandregulationsmentioned
above.
11. WIRING DIAGRAM
See technical details of the corresponding actors.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Niko XX-781 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Niko XX-781 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info