710751
87
Verklein
Vergroot
Pagina terug
1/302
Pagina verder
GS108T and GS110TP Smart Switch Software Administration Manual
Configuring Switching Information 3-3
v1.0, April 2010
Port Speed. Use the menu to select the port’s speed and duplex mode. If you select Auto,
the duplex mode and speed will be set by the auto-negotiation process. The port’s
maximum capability (full duplex and 1000 Mbps) will be advertised. Otherwise, your
selection will determine the port’s duplex mode and transmission rate. The factory default
is Auto.
Sleep Mode. Use the menu to select the port’s Green Ethernet mode, which can be one of
the following:
Enable: Specifies that when the port link is down, the port automatically goes down
for a short amount of time and wakes up to check link pulses. When the port does not
have a link partner, the sleep mode reduces power consumption.
Disable: The port provides full power to the port even if there is no link partner.
Short Cable Mode. Use the menu to select the port’s Green Ethernet mode, which can be
one of the following:
Enable: Specifies that cable test is performed when the port link is up at 1 Gbps and if
the cable is less than 10m, PHYs are placed in low power mode (nominal power).
Disable: The port does not participate in Green Ethernet mode.
Physical Status. Indicates the physical port’s speed and duplex mode
Link Status. Indicates whether the Link is up or down.
Link Trap. This object determines whether or not to send a trap when link status changes.
The factory default is Enable.
Enable: Specifies that the system sends a trap when the link status changes.
Disable: Specifies that the system does not send a trap when the link status changes.
Maximum Frame Size. Specify the maximum Ethernet frame size the interface supports
or is configured to support. The frame size includes the Ethernet header, CRC, and
payload. (1518–9216). The default maximum frame size is 1518.
MAC Address. Displays the physical address of the specified interface.
PortList Bit Offset. Displays the bit offset value which corresponds to the port when the
MIB object type PortList is used to manage in SNMP.
ifIndex. The ifIndex of the interface table entry associated with this port. If the interface
field is set to All, this field is blank.
6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to the
latest value of the switch.
7. If you make any changes to the page, click Apply to apply the changes to the system.
87

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Netgear GS108Tv2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Netgear GS108Tv2 in de taal/talen: Engels als bijlage per email.

De handleiding is 27,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Netgear GS108Tv2

Netgear GS108Tv2 Installatiehandleiding - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info