637928
24
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
24
Wall Mounting Instructions:
1. Using the two holes provided in the vertical tube, mount the
bracket to the wall.
2. Ensure minimum clearance to combustibles are maintained, 4”
(100mm) to sides, and 6”(150mm) from the rear.
3. Do not locate the grill under unprotected combustible construction.
4.The platform may be swivelled by removing the two #8 x 3/8”
flathead phillips screws and turning the platform to the desired angle.
Replace the two screws and tighten.
5. Once the platform is located in the desired position, the grill can be
mounted:
a. Lock the lid of the grill closed with the latch.
b. Hold the grill by the handle with one hand, place the other hand under the grill in the
centre of the front tapered surface.
c. Place the grill bottom on the platform and slide it forward to engage the tab protruding from
the bottom of the grill. Ensure that the tab is properly engaged.
d. When the dimples on the bottom of the unit line up with the holes on the platform, the latch is
ready to be fastened.
6. Once the grill has been attached, thread the regulator (clockwise) into the regulator mount.
On tube burner version, lift the burner slightly to align it with the orifice. Tighten by hand.
7. To fasten the regulator locking bracket, locate it at the bottom back corner of the regulator mount and turn the regulator until the
gas inlet is aligned with the hole in the regulator locking bracket. Slide the locking bracket forward until the two tabs engage into the
slots on the regulator mount. Tap in firmly.
8. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread the cylinder.)
Trailer Ball Mounting Instructions:
1. Place the ball mount over the ball on your drawbar or bumper.
2.Tighten the two wing screws until the mount is firmly held in place.
3. Once the mounting arm is tight, the grill can be mounted:
a. Lock the lid of the grill closed with the latch.
b. Hold the grill by the handle with one hand, place the other hand
under the grill in the centre of the front tapered surface.
c. Place the grill bottom on the platform and slide it forward to
engage the tab protruding from the bottom of the grill. Ensure that the
tab is properly engaged.
d. When the dimples on the bottom of the unit line up with the holes on the
platform, the latch is ready to be fastened.
4. Once the grill has been attached, thread the regulator (clockwise) into the regulator
mount. On tube burner version, lift the burner slightly to align it with the orifice. Tighten
by hand.
5. To fasten the regulator locking bracket, locate it at the bottom back corner of the
regulator mount and turn the regulator until the gas inlet is aligned with the hole in the
regulator locking bracket. Slide the locking bracket forward until the two tabs engage into
the slots on the regulator mount. Tap in firmly.
6. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread
the cylinder.)
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Napoleon PTSS215PI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Napoleon PTSS215PI in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 1,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info