161044
6
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
6
ENGLISH FRANÇAIS
DEUTSCH
NEDERLANDS
ESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
FRONT PANEL CONTROLS FIGURE 2
1 Power On/Off (TNR 1 Figure 3) - POWER switches the tuner on
or off. Pressing the Power switch turns the Tuner on, the Display
Panel and Power Status Indicator (No. 2) will light up. Pressing the
Power button again will switch the unit off.
NOTE
The C 425 has a receiver for remote control commands built-in. Most
NAD system remote control handsets with an On/Off toggle button
or separate On and Off button will be able to switch the tuner from
On to Stand-by and vice-versa.
The C 425 uses a memory back-up system to store Preset
information. This information is retained for several weeks, even if
the unit is switched off completely or unplugged. When switching
power On, the C 425 will go back to the station last tuned to before
the unit was turned off. This will allow you to make timer recordings
using an external timer and recorder.
2 Power Status Indicator - The Power Status Indicator will light up
green when Power is on. When the tuner is switched to Stand-by
mode (through either a remote control or the 12V trigger input) the
indicator will light up amber. When the unit is switched off
completely, it is off.
3 Blend (TNR 1 Figure 3) - Weak or remote stereo radio stations
are sometimes received with noise and hiss as the antenna signal is
too weak. By switching the tuner to mono will reduce the amount of
noise and hiss but at the expense of any stereo information. The NAD
Blend feature will allow you to reduce the amount noise and hiss but
still retain some level of stereo separation, instead of mono. The
Blend button toggles between engaging or disengaging the Blend
feature; when engaged, "BLEND" lights up in the display.
NOTE
The "Blend" status can be stored for individual presets. Refer to the
separate chapter "Storing, Recalling and Labelling Presets" for more
information.
4 Memory - The Memory is used to store stations into the Preset
Memory bank and to store user defined names for non-RDS Preset
stations. When Memory is pressed during normal operation, the
Preset number and the red "MEMORY" indicator will flash in the
Display Panel. If no other buttons are pressed within 12 seconds, the
tuner will revert to its previous state. Refer to the separate chapter
"Storing, Recalling and Labelling Presets" for more information.
5 FM Mute/Mode (TNR 1 Figure 3) - This button combines two
functions; it switches the tuner from Stereo to Mono and disengages
the muting circuitry at the same time. The muting circuit will mute
the tuner in between radio stations when searching or tuning. This
way the tuning noise is avoided. The muting circuit however may
suppress very weak radio station signals. If a weak station is in stereo
it will have a high level of background hiss. Switching to Mono Mode
and disengaging the muting circuit by depressing the FM
MUTE/MODE button will allow the station to be heard and will cancel
most or all of this background noise.
In normal operation the mute circuit is engaged, the display indicates
"FM MUTE". Press the FM Mute/Mode button to disengage the
muting circuit and switch from stereo to mono reception. "FM
MUTE" in the display will extinguish. Press the FM Mute/Mode switch
again to return to Auto Stereo FM operation.
NOTE
The "FM Mute/Mode" status can be stored for individual presets.
Refer to the separate chapter "Storing, Recalling and Labelling
Presets" for more information.
6 AM/FM (TNR 1 Figure 3)- The AM/FM button switches the tuner
from the AM band to the FM band and vice-versa. The Display Panel
shows the frequency of the tuned station and which band is selected.
The FM tuning is in 0.05 MHz increments, AM tuning is in 9 kHz or
10 kHz increments, depending on the version.
7 Display (TNR 1 Figure 3)- With stations carrying RDS
information, The Display button scrolls between three different
display modes, each successive push of the button engages the next
one of the three modes:
a) In the default mode, the station’s RDS name is displayed, Program
Service (PS; normally the station’s calling letters, BBC R3, for
instance).
b) From the default mode, press the button once to view Radio Text
(RT). This can be additional information such as the presenter’s or
program’s name; what song is playing, etc. This text scrolls
continuously over the 8 alphanumeric display segments.
c) Press the button from the display RT mode to display the station
frequency. Press again to return to the default mode (a).
When tuned to a non-RDS station - The Display button toggles
the display to show either the station frequency or user entered
station name. If no user name was entered the display will indicate
"NO RDS". The Display button is also used to label non-RDS stations
with a name. Refer to the separate chapter "Storing, Recalling and
Labelling Presets" for more information.
Introduction
C425 072006.qxd 7/28/2006 11:31 AM Page 6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD c425 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD c425 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info