745052
6
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
ENGLISH
6
1 BALANCED
Connect XLR audio source to these connectors. Ensure that proper
pin congurations are followed – Pin 1: Ground, Pin 2: Positive
(signal live) and Pin 3: Negative (signal return).
2 SELECT
Use SELECT switch to choose which audio input will be the active
source.
Select SINGLE-ENDED audio input by setting SELECT switch to the
right towards the direction of SINGLE ENDED input.
Select BALANCED audio input by setting SELECT switch to the left
towards the direction of BALANCED input.
3 SINGLE-ENDED
Use a twin RCA-to-RCA lead to connect these sockets to the
left and right analog output of a preamplier, processor or any
compatible device.
4 GROUND
Ensure that the C 298 is plugged-in to a grounded AC wall outlet.
If a separate earth ground is necessary, use this terminal to ground
your C 298. The C 298 can be connected to ground by connecting
a ground lead wire or similar to this terminal. After insertion, tighten
the terminal to secure the lead.
5 LINE OUT
The LINE OUT sockets allow daisy-chaining” - use more than one
amplier to add speakers to the same channel.
Use dual RCA cable to connect LINE OUT to the corresponding
analog audio input of compatible devices such as ampliers,
receivers or other applicable devices.
6 INPUT SELECT
Use INPUT SELECT switch to manage audio output level.
• FIX: Audio output level is xed. The C 298 becomes like a basic
amplier with audio output level controlled by an external device.
• VAR: Audio output level can be adjusted using the INPUT LEVEL
control knob.
7 INPUT LEVEL
With INPUT SELECT switch set to VAR, the INPUT LEVEL control knob
can be used to adjust the audio output level of the C 298.
Turn clockwise to increase audio output level; counter clockwise to
lower it.
NOTE
The INPUT LEVEL is a level trim only and not a full volume control.
8 AUTO SENSE LEVEL
Auto Sense feature instantaneously turn the C 298 to operating mode
from standby mode if it senses a specic input signal level applied to
either the BALANCED or SINGLE-ENDED sockets. There are three Auto
Sense levels
SETTING INPUT LEVEL
Low 0.85 mV
Mid 1.7 mV
High 3.7 mV
Auto Sense mode can be enabled or disabled by the following steps.
Enable Auto Sense mode
At operating mode, press and hold front panel Standby button and
then release within 10-15 seconds. The Bridge mode indicator light
ashes three times.
Disable Auto Sense mode
At operating mode, press and hold front panel Standby button and
then release within 10-15 seconds. The Bridge mode indicator light
ashes two times.
9 SERVICE
Use for servicing purposes only. Not for consumer use.
IDENTIFICATION OF CONTROLS
REAR PANEL
© NAD C 298
2 3 5 6 7 8 9 10
1 4 13
12 14 1511
ATTENTION!
Please make sure that the C 298 is powered o or unplugged from the mains power source before making any connections. It is also advisable to power
down or unplug all associated components while making or breaking any signal or AC power connections.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD C298 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD C298 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van NAD C298

NAD C298 Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info