493502
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
IDENTIFICATION OF CONTROLS
REAR PANEL
4 BRIDGE MODE: The C 275BEE amplier can be congured to be
MONO (Bridge Mode), more than doubling its output power. This way,
the C 275BEE can be used as part of a high power stereo or home-
theatre system, by connecting additional power ampliers.
In BRIDGED MODE, the C 275BEE will produce approximately 330W into
an 8 ohm loudspeaker. In this mode, the amplier sections will react
as though the speaker impedance has been halved. Low impedance
speakers (under 8 ohms) are not recommended when using Bridge
Mode as these may cause the ampliers thermal cut-out to operate if
played at high levels.
Set the BRIDGE MODE switch to the “ON” position and connect the
speaker to the terminals marked “L +” and “R+” ensuring that the “L+”
is connected to the “+” terminal of your loudspeaker and the “R+” is
connected to the loudspeakers “ - ” terminal. Connect the source to
the INPUT sockets.
The BRIDGE MODE indicator on the front panel will illuminate when the
C 275BEE is in Bridge mode.
NOTE
Do not connect anything to the Right Input socket when Bridge Mode
is selected.
5 SOFT CLIPPING™: Enables NAD’s proprietary Soft Clipping circuitry
on all channels. At [ON] position, Soft Clipping gently limits the output
of the C 275BEE to minimize audible distortion should the amplier be
over-driven. Soft Clipping may simply be left ON at all times to reduce
the likelihood of audible distortion from excessive volume settings.
However, for critical listening and to preserve optimum dynamics, you
may wish to defeat it by setting this switch to “OFF” position.
The SOFT CLIPPING indicator on the front panel will illuminate when the
amplier is in Soft Clipping mode.
6 +12V TRIGGER IN/INPUT SENSE - OFF/AUTO: The OFF/AUTO switch
is applicable for INPUT SENSE only. At AUTO setting, the C275BEE will
instantaneously turn ON from standby mode if it senses any input signal
(approximately above 20mV RMS input) applied through the INPUT
sockets.
In the absence of any input signal at the INPUT sockets and with OFF/
AUTO switch set to AUTO, the C275BEE will switch to standby mode.
Slide the OFF/AUTO switch to OFF setting for the C275BEE to be
normally switched ON (or back to standby mode) using the front panel
STANDBY button.
IMPORTANT NOTES!
At input sense mode, it will take about 10 minutes for the C275BEE to
go to standby mode when the input signal source is turned OFF or goes
below 20 mV.
If the C275BEE is switched ON via INPUT SENSE mode, it cannot be
switched back to standby mode via the front panel STANDBY button. The
C275BEE will switch back to standby mode in the same manner it was
activated. For the C275BEE to go to standby mode, the input signal can
be completely turned o or brought down to a level lower than 20mV.
7 +12V TRIGGER INPUT: The +12V Trigger input allows the C 275BEE
to be switched remotely from standby mode to ON and vice-versa
by ancillary equipments such as a preamplier, AV processor, etc. The
controlling device must be equipped with a 12V trigger output to use
this feature.
8 FUSE HOLDER: In the unlikely event a fuse may need to be replaced,
unplug the AC cord from the wall. Then, remove all connections from
the amplier. Use a athead screw driver or similar to open the fuse
holder via the slot indicated. With the screw driver in place, push and
turn counterclockwise to open the fuse holder. Only replace the
fuse with the same type, size, and specication – T10AL 250V for 120V
version or T5AL 250V for 230V version.
IMPORTANT NOTICE
Do not use any substitute fuses of dierent types or with dierent ratings
or values. Failure to observe this precaution may cause damage to the
amplier circuits and may create a re hazard and/or defeat the safety
built into the amplier and may void the warranty.
9 SPEAKERS A, B: The C 275BEE is equipped with two sets of speaker
connectors. Use the Speakers A terminals for the “main speakers and
use the Speakers B terminals for a second pair, for example, extension
speakers located in another room.
Connect the right speaker to the terminals marked “R +” and “R-” ensuring
that the “R+” is connected to the “+” terminal on your loudspeaker and the
“R-” is connected to the loudspeakers “-” terminal. Connect the terminals
marked “L+” and “L-” to the left speaker in the same way.
In Bridge Mode, connect the single speaker to the terminals marked
“R +” and “L+” ensuring that the “L+” is connected to the “+” terminal
on your loudspeaker and the “R+” is connected to the loudspeakers “-”
terminal. Refer also to the section above about “BRIDGE MODE.
Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire to
connect loudspeakers to your NAD C 275BEE. The high-current binding
post terminals can be used as a screw terminal for cables terminating in
spade or pin sockets or for cables with bare wire ends.
10 AC MAINS INPUT: The C 275BEE comes supplied with a separate AC Mains
cable. Before connecting the cable to a live wall socket ensure that it is
rmly connected to the C 275BEE’s AC Mains input socket rst. Connect
only to the prescribed AC Outlet, i.e., 120V 60 Hz or 230V 50 Hz. Always
disconnect the AC Mains cable plug from the live wall socket rst, before
disconnecting the cable from the C 275BEE’s Mains input socket.
11 POWER SWITCH: The POWER switch supplies the master AC mains
power for the C 275BEE. Refer to the ATO LOGIC chart below for a better
understanding of the role of the POWER switch when switching ON
or OFF the C 275BEE. If you intend not to use the C 275BEE for long
periods of time (such as when on vacation), switch the POWER switch
to the OFF position.
8
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw NAD C 275 BEE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van NAD C 275 BEE in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van NAD C 275 BEE

NAD C 275 BEE Gebruiksaanwijzing - Nederlands - 12 pagina's

NAD C 275 BEE Gebruiksaanwijzing - Deutsch - 12 pagina's

NAD C 275 BEE Gebruiksaanwijzing - Français - 12 pagina's

NAD C 275 BEE Gebruiksaanwijzing - Italiano - 12 pagina's

NAD C 275 BEE Gebruiksaanwijzing - Espanõl - 12 pagina's

NAD C 275 BEE Gebruiksaanwijzing - Svenska - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info