AHD Colour Camera
These instructions are intended for
installers of video surveillance systems.
Please read these instructions carefully
prior to installing the camera and keep
them for later reference.
1 Applications
This colour camera is especially designed for
video surveillance systems (CCTV). Featur-
ing AHD technology (Analog High Definition),
the camera supports the transmission of
high-resolution analog video signals (720p)
via standard coaxial cables with a length of
up to 300 m. Due to its robust metal spherical
housing, the camera is vandal-proof and
weather-proof (IP 66) and is therefore also
suitable for outdoor applications. When dark-
ness falls, the IR LEDs (5) will illuminate a
surveillance area of up to 10 m and the cam-
era will switch to B / W mode.
2 Important Notes
The camera corresponds to all relevant direc-
tives of the EU and is therefore marked
with
.
G
Protect the camera against extreme tem-
peratures (admissible ambient tempera-
ture range: −10 °C to +55 °C).
G
Do not use aggressive detergents or chem-
icals for cleaning the camera.
G
No guarantee claims for the camera and no
liability for any resulting personal damage
or material damage will be accepted if the
camera is used for other purposes than
originally intended, if it is not correctly in-
stalled, or if it is not repaired in an expert
way.
If the camera is to be put out of oper-
ation definitively, take it to a local re-
cycling plant for a disposal which is
not harmful to the environment.
3 Installation
1) Make a test run to determine the optimum
mounting location.
2) For installation, remove the base (1) from
the support: Remove the three screws of
the outer support ring (2). At the mounting
location, drill three holes for fixing the base
and, if necessary, drill a hole for the con-
nection cable (alternatively, the cable can
be guided through one of the two cable
inlets at the side of the base). Fasten the
base with the mounting material provided.
3) Place the camera (4) with the inner support
ring (3) and the outer support ring (2) onto
the base (1). To be able to align the cam-
era to the surveillance zone after it has
been set into operation, for the time being
only fasten the outer support ring onto the
base so that the camera can still be
moved.
4) Connect the yellow BNC plug (8) to the input
of an AHD compatible video recorder (e. g.
from the AHR series from MONACOR).
5) Connect a regulated 12 V power supply
unit with a permanent rating of 400 mA
to the inline jack (7). A low-voltage plug
5.5/2.1 mm (exterior / interior diameter) is
required. Make absolutely sure to observe
the correct polarity (centre contact = +).
6) Please observe the following for outdoor
installations:
The connections (7, 8) and the cable split-
ter (6) are not weather-proof and must be
protected accordingly.
CAUTION The infrared LEDs will switch
on when darkness falls. When setting up
the camera, never look directly into the lit
infrared LEDs from a close range. The
infrared light may cause eye irritation.
However, the infrared radiation is far
below the emission limit and rated risk-
free according to EN 62471.
7) Switch on the video recorder and the mon-
itor connected and then align the camera
by means of the monitor image: Turn the
camera in the inner support ring and turn
the inner ring in the outer ring as desired.
8) After the alignment, fasten the three
screws to fix the outer support ring on the
base.
4 Specifications
Image sensor: . . . . . . . . . . CMOS chip,
8.5 mm (
³
″)
Number of pixels: . . . . . . . 1280 × 720
Resolution: . . . . . . . . . . . . 720p / 25
Colour modulation system: PAL
Lens: . . . . . . . . . . . . . . . . . 3.6 mm / 1 : 1.2
Minimum illumination: . . . . 0.08 lx
Electronic shutter: . . . . . . .
1
⁄25 –
1
⁄10 000 s
Video output: . . . . . . . . . . 1 Vpp / 75 Ω
IR LEDs, range: . . . . . . . . 30 LEDs, 10 m
Power supply: . . . . . . . . . 12 V
±10 %,
400 mA
Ambient temperature: . . . . −10 °C to +55 °C
Protection: . . . . . . . . . . . . IP 66
Dimensions: . . . . . . . . . . . ∅ 105 × 60 mm
Weight: . . . . . . . . . . . . . . . 350 g
Subject to technical modification.
AHCAM-310DF
Order number 18.4210
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved. A-1642.99.01.03.2015
®
English
