729402
5
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
RouterBOARD 750 Series User's Manual
5
An alternative configuration option is the MikroTik Winbox utility (Windows only). Winbox can be used to
connect to the default IP address of 192.168.88.1 with the username admin and no password.
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET
button of the device when starting it until the LED light turns off, and the device will start to look for Netinstall
servers. In case IP connection is not available, Winbox can also be used to connect to the MAC address of the
device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup
Onboard NAND Storage Device
The RouterBOARD may be started from the onboard NAND storage chip. As there is no partition table on the
device, the boot loader assumes the first 4MiB form a YAFFS filesystem, and executes the file called “kernel”
stored in the root directory on that partition. It is possible to partition the rest of the medium by patching the
kernel source.
Booting from network
You can boot the RouterBOARD device from Network with the NETINSTALL software, if your RouterOS
software needs to be reinstalled or reset. Hold the Reset button, power on the device, and release until the
LED light stops flashing. See Buttons and Jumpers below for details. The Netinstall program can be
downloaded from
www.mikrotik.com download section.
Network boot works similarly to PXE or EtherBoot protocol, and allows you to the device from an executable
image stored on a TFTP server. It uses BOOTP or DHCP (configurable in boot loader) protocol to get a valid IP
address, and TFTP protocol to download an executable (ELF) kernel image combined with the initial RAM disk
(inserted as an ELF section) to boot from (the TFTP server's IP address and the image name must be sent by the
BOOTP/DHCP server).
To boot the RouterBOARD computer from Ethernet network you need the following:
An ELF kernel image for the loader to boot from (you can embed the kernel parameters and initrd image
as ELF sections called kernparm and initrd respectively)
A TFTP server which to download the image from
A BOOTP/DHCP server (may be installed on the same machine as the TFTP server) to give an IP address,
TFTP server address and boot image name
Operating System Support
MikroTik RouterOS starting from version v5 is fully compatible with the device. If your device is preinstalled
with an earlier RouterOS release, please upgrade RouterOS to v5.8 or newer.
Buttons and Jumpers
RouterOS reset jumper hole (on the bottom of case) resets RouterOS software to defaults. Must
short circuit the metallic sides of the hole with a screwdriver and boot the device. Hold screwdriver in
place until RouterOS configuration is cleared.
RouterBOOT reset button (RES, front panel) has two functions:
o Hold this button during boot time until LED light starts flashing, release the button to reset
RouterOS configuration (same result as with RouterOS reset hole)
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mikrotik RB750R2 - hEX lite bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mikrotik RB750R2 - hEX lite in de taal/talen: Engels als bijlage per email.

De handleiding is 0,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info