658471
140
Verklein
Vergroot
Pagina terug
1/666
Pagina verder
100 Chapter 9: Basic Operation
PRO Series Live Audio Systems
Owner’s Manual
>> To set the stage box gain/console gain
1 In the gain trim section of an input fast strip, press the quick access button (see
Figure 15 “Gain and filter sections of the input strips” on page 99). This selects
the input channel and assigns its configuration processing area to GUI channel
strip, which contains the GAIN SWAP button.
2 Press the left-right arrow gain swap button
(or click GAIN SWAP) to swap the gain
trim and stage box sections over. The
diagram right shows an example of each
section.
3 Adjust the gain trim control knob (5dB
steps from -2.5dB to +45dB) to the
required level to suit the Midas pre-amp
characteristic. A suitable level could be one
that only just illuminates the yellow LEDs. Do this for each required channel.
Drive the mic amps for that ‘Midas colouration’; feel free to overdrive if you want.
4 After you have achieved the required gain state, press the left-right arrow gain
swap button (or click GAIN SWAP) to swap the gains back to their default state.
5 Adjust the gain trim control knob to (this time) adjust the console digital trim
(+20dB to -40dB continuous trim) for your preferred gain structure.
6 Set analogue remotes for initial set-up, then adjust digital trim for showtime.
Setting the high and low pass filters
Select high and low pass filters. The high and low pass filters can be switched on/off
and, when on, each has two settings. The filters are replicated on the GUI, which also
shows the value of the filter in operation.
>> To set both high and low pass filters in
1 In the gain trim section of an input fast strip (see Figure 15 “Gain and filter
sections of the input strips” on page 99), press the quick access button. This
selects the input channel and assigns its configuration processing area to the GUI
channel strip, which contains the filters section.
2 In the filters section of the input channel strip, press the filter select button
(high pass or low pass ) to switch the filter in.
3 If necessary, press the filters SLOPE button to set its slope (dB); its status is
shown on the GUI. For the high pass filter, in = 24dB and out = 12dB, and for the
low pass filter, in = 12dB and out = 6dB.
4 Adjust the high pass/low pass control knob to set the filter frequency (Hz).
The ranges are 10Hz to 400Hz for the high pass filter and 2kHz to 40kHz for the
low pass filter.
140

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midas PRO3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midas PRO3 in de taal/talen: Engels als bijlage per email.

De handleiding is 30,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info