658492
25
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
11
DL461 Router
Operator Manual
Chapter 4: Getting Started
This chapter shows you how to connect up, switch on, set up and configure the DL461
Router.
Note: The DL461 Router is operated from the XL8 Control Centre only. For more
information, see the XL8 Live Performance System Owner’s Manual (part number
DOC02-XL8).
Connecting up (XL8 system)
There are two DL461 Routers, X and Y, in the standard XL8 system configuration. As
the routers form the hub of the XL8 Live Performance System, system set-up involves
connecting up both DL461 Routers with the DL471 DSPs, DL431 Mic Splitters, DL451
Modular I/Os and the XL8 Control Centre.
>> To connect up the X router
Refer to Figure 1 on page 12.
1 In AES50 audio - bank 0, connect the 10 sockets to the X AES50 audio socket
on the 10 DSP units.
2 In AES50 audio - bank 1, connect socket 1 to the X AES50 audio socket (A or
B, depending on mic amp selection) on Mic splitter 1. Similarly, connect sockets
2, 3 and 4 in this bank to the other three mic splitters.
3 In AES50 audio - bank 1, connect socket 5 to the X AES50 audio socket on the
I/O unit.
4 In the Ethernet control bank of connectors, connect the 10 sockets to the X
Ethernet control socket on the 10 DSP units.
5 Connect the AES50 synchronisation (word clock or AES3 sync), if required (see
“Rear panel connections” on page 8).
6 Connect the snake (optical or CAT6e) to rear of control centre (see “Rear panel
connections” on page 8).
7 Mains power supply - insert the IEC connector of the mains cable into the rear
of the unit and then plug it into the mains power outlet.
The connection configuration for AES50 audio banks 0 and 1 has been derived for
optimum accessibility and convenience. However, these connections are flexible,
so you can swap the bank connections over or reallocate the mic splitter and I/O
connections within their respective bank, if you want.
>> To connect up the Y router
Follow the procedure for connecting the X router, but use the Y connections where
available.
>> To connect the X and Y routers together
In the control expansion section (rear panel) of the X router, connect the router/
router interconnection cable to the Ethernet socket. Then, connect the other end of
the cable to the equivalent socket on the Y router.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Midas DL461 Router bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Midas DL461 Router in de taal/talen: Engels als bijlage per email.

De handleiding is 6,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info