658520
25
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
25
ENGLISH
7.1 Sawing
1. Choose and install a table insert
extrusion suitable for the type of cut
to be performed:
table insert extrusion with a
narrow slot for standard cross
cuts only;
table insert extrusion with bev-
elled slot for bevel cuts also.
2. Adjust the band saw blade speed.
3. If necessary, adjust the table tilt.
A
Risk of kickback (work piece is
caught by the band saw blade and
thrown against the operator)!
Do not jam any work pieces.
4. Select rip fence and table tilt for the
type of cutting operation to be car
-
ried out.
A
Hazard due to jamming of the
tool!
When cutting with the ripping fence
and inclined workpiece, the ripping
fence has to be mounted at the side
of the workpiece inclined down
-
wards.
5. Set upper blade guide 3 mm above
the work piece.
3
Note:
Always make a trial cut in a piece
of scrap to verify settings; correct if nec-
essary before cutting the work piece.
6. Place work piece on the saw table.
7. Plug in.
8. Start saw.
9. Cut work piece in a single pass.
10. Switch off if no further cutting is to be
done immediately afterwards.
A
Danger!
Prior to all servicing:
1. Switch machine OFF;
2. Wait until the saw has come to a
complete stop.
3. Unplug power cable;
Check to see that all safety devices
are operational again after each ser
-
vice.
Replace defective parts, especially
of safety devices, only with genuine
replacement parts. Parts not tested
and approved by the manufacturer
can cause unforeseen damage.
Repair and maintenance work other
than described in this section should
only be carried out by qualified spe
-
cialists.
8.1 Changing the Band Saw
Blade
A
Danger!
Risk of injury, even with the
band saw blade at standstill. Wear
gloves when changing blades.
Use only suitable band saw blades
(see "Technical Specifications").
1. Loosen the four thumb screws (71)
and remove the fence guide extru-
sion (72).
2. Open both housing doors.
3. Swing the lower blade guard open.
4. Set the upper blade guide (73) to its
lowest position.
5. Loosen quick release lever (74) until
the band saw blade has slackened.
6. To remove the band saw blade,
guide it through
the slot in the saw table (75),
the blade guard on the upper
blade guide (76),
the blade cover on the saw
housing
(77) and
the blade guides.
7. Fit a fresh band saw blade. Observe
correct position: the teeth point
towards the front (door) side of the
saw.
8. Center band saw blade on the rub-
ber tyres of the band saw wheels.
9. Tighten quick release lever until
blade does no longer slip off the
band saw wheels.
10. Close lower blade guard .
A
Danger!
Close housing doors only
when the lower blade guard is in its
closed position.
11. Close both housing doors.
12. Then:
tension band saw blade (see
"Initial operation");
align band saw blade (see
"Care and Maintenance");
align blade guides (see "Care
and Maintenance");
let saw test run for at least one
minute;
stop saw, unplug and recheck
settings.
8.2 Aligning the Band Saw
Blade
If the band saw blade does not run in the
centre of the rubber tyres, the tracking
needs to be corrected by adjusting the tilt
of the upper band saw wheel:
1. Loosen lock nut (78).
2. Turn setting knob (79):
Turn setting knob (79) clock-
wise if the band saw blade
runs towards the front of the
saw.
Turn setting knob (79) coun-
ter-clockwise if the band saw
blade runs towards the rear of
the saw.
3. Tighten lock nut (78).
8.3 Aligning the Upper Blade
Guide
The upper blade guide consists of:
a thrust bearing (supporting the band
saw blade from the rear),
two guide bearings (providing lateral
support).
8. Care and Maintenance
71
72
73
74
75
76
77
78 79
25

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Metabo-BAS-317-Precision

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BAS 317 Precision bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BAS 317 Precision in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 6,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Metabo BAS 317 Precision

Metabo BAS 317 Precision Gebruiksaanwijzing - Nederlands, Português, Espanõl - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info