122407
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
SET-UP
Read these instructions
carefully before programming
your remote control!
MAKE SEARCH PROGRAMMING MODE
A
1.Turn ON the appliance:
– if a VCR, insert a cassette
– if SAT, select a program
– if DVD, insert a DVD.
2. In the code book enclosed, look for the
make of your appliance and make a
note of the code indicated at the side
(e.g. Philips 001) or the code for the
make indicated by the arrow.
3.Press and release the TV - VCR - SAT -
DVD selection button for the appliance
you want to use:
– the TV button is used to search only
for the TVs of the make selected
– the VCR button is used to search only
for the VCRs of the make selected
– the SAT button is used to search only
for the SATs of the make selected
– the DVD button is used to search only
for the DVDs of the make selected.
4. Hold down the SHIFT and ON/OFF
buttons together until the TV - VCR -
SAT - DVD selection buttons
start to flash indicating that the
remote control is programming.
5. Release the buttons. Within 15
seconds, enter the make code
previously identified (e.g. 001).
The TV- VCR - SAT -DVD selection
button flashes more quickly to indicate
that the remote control is ready for the
search.
6. Point the remote control at the
appliance. Press and release one of
the most frequently used keys several
times STOPPING when the appliance
responds correctly to the command.
7. When the appliance responds
correctly, press SHIFT to confirm.
Three flashes indicate that the
operation has been completed
correctly.
Identify and make a note of the code
for the appliance which you have
searched for following the code
noting procedure (see “NOTING THE
PROGRAMMED CODE” section).
Warning: program one appliance at a time.
SHIFT
SHIFT
FITTING THE BATTERIES
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries.
Insert the batteries as shown.
• The batteries must be changed once a year.
• If the TV - VCR - SAT - DVD/ selection buttons start
to flash during use, this indicates that the batteries
are low and should be changed.
• When you remove the batteries, fit the new ones
within 5 minutes or you may have to reprogram your
remote control.
Make a note of the codes for the TV - VCR - SAT -
DVD equipment on the adhesive label inside the
battery cover. This note will be handy if you have to
reprogram your control.
TV
DVD
0
0
1
SAT
VCR
NOTE: THE SELECTION BUTTON
STOPS FLASHING.
The remote control leaves the
programming mode and the
TV - VCR - SAT - DVD selection
button stops flashing:
if no buttons are pressed for 15 seconds
if an invalid make code is entered
if the code search list is completed. In
this case, go back to point 3 or switch to
programming mode C
if you press the TV - VCR - SAT - DVD -
F1 - F2 - F3 - F4 buttons by mistake.
To program the Universal 4 remote
control, follow the indications
in section A , B or C .
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Meliconi universal 4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Meliconi universal 4 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info