478435
13
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
ENGLISH - 10
and lower cut. The meeting point between the two
sides of the notch is called “directional cut line” This
line must be perfectly horizontal at right angles (90°)
to the felling direction.
The felling cut that provokes the tree fall, is performed
at 3 to 5 cm above the lower part of the directional
felling cut line, finishing at a distance of 1/10 of the
trunk from the notch. Remain on the left hand side of
the tree and cut using the chain pulling method and
the spiked bumper. Check that the tree does not
move in a direction other than that predicted for the
fall. As soon as possible insert a felling lever or
wedge into the cut. The uncut part of the trunk is
called the “hinge”, as it is intended to guide the tree
as it falls; in cases where the cuts are not sufficient,
not straight, or have been cut through completely, the
tree fall cannot be controlled (extremely dangerous!).
For this reason the various cuts must be performed
with great precision.
When cutting operations are completed the tree will
begin to fall. Where necessary help tree fall using
wedges or felling levers
.
Limbing
Once the tree has been felled, the trunk must be
limbed: in other words, the branches are removed
from the trunk. Do not underestimate this operation
because the large majority of kickback accidents
occur during this stage. For this reason pay close
attention to the position of the bar nose during cutting
operations and always work on the left hand side of
the trunk.
I. ENVIRONMENTAL INFORMATION
This section contains information useful for maintaining the characteristic of ecocompatibility included in the
origin design of the machine, and as regards proper use and disposal of chain oil
DESIGN
In the design stage, care was taken to develop an engine with reduced consumption and low emission of noise.
USE OF THE MACHINE
The operations of filling the oil tank should be carried out in such a way as to avoid spilling oil and contaminating
the soil and the environment.
DISPOSAL
Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized
organization for proper disposal in compliance with the regulation in force.
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product, please contact your local
council office, your household waste disposal service or the shop where you purchased the product.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

McCulloch-Electramac

Zoeken resetten

  • Ik bezit een electromac 240. Nu is de oliesmeerleiding verteerd en moet ik die vernieuwen. Vanaf het tankje naar de pomp is de loop van de leiding mij wel duidelijk maar vanaf de pomp naar het zaagblad is voor mij een raadsel. Kunnen jullie mij vertellen hoe die leiding loopt?
    Alvast bedankt voor de moeite
    Groet
    roelof van Bruggen Gesteld op 6-5-2020 om 18:28

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw McCulloch Electramac bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van McCulloch Electramac in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info