3 Press and hold the green button while re-installing the batteries.
4 Continue holding the green button for approximately five
seconds (from step 3 to step 4, do not release the button) until
the safe beeps twice.
5 ALL the fingerprint registrations have been deleted, the
fingerprint memory is empty and the safe is set back to the
factory default setting. Any fingerprint can now open the door.
Additional Notes: A single fingerprint cannot be deleted. If you
need to delete a user, all the fingerprints will need to be deleted
and users will need to re-register.
To open the safe with the
battery jump kit:
If battery power in the safe is running low and cannot operate the
safe, or if the override key is misplaced, you can use the USB battery
jump kit (the battery case with the attached power cord) to open
the safe.
Important: This should not be used as a primary means to open
the safe.
1 Install 4 new AA alkaline batteries in the battery case of the
jump kit.
2 Remove the magnetic security cover on the right side of the safe
control panel.
3Insert the Micro USB cord into the USB slot of the safe.
4Scan a registered fingerprint and the safe will operate normally.
5 Remove the Micro USB cord and replace the security cover on
the control panel.
6Install 4 new AA alkaline batteries in the safe.
Bolt-Down Instructions:
To help provide maximum security, it is highly recommended that you
bolt down your safe.
1 Set the safe in the place you intend to bolt it down and open the
door.
2 Using a pencil mark the floor or wall through the holes provided
in the bottom or back of your safe.
3 Move the safe away and drill holes of the appropriate diameter
and depth for the type of hardware being used.
4 Place the safe back over the holes and install the fasteners as
required.
Note: It is not recommended to attempt to bolt your safe to
both the floor and wall. If bolting to a wall, please ensure the
safe is resting on a supporting surface such as a table or shelf.
Thank you for choosing Master Lock/SentrySafe to store all your important documents and valuables.
We hope that this product will help you stay organized and provide you with the peace-of-mind of knowing the things most important to you are protected.
Important security note: Biometric safe models will initially open with ANY fingerprint, therefore it is important to re-program the safe with your fingerprints to provide
maximum security. Fingerprint memory has a maximum capacity of 30 fingerprint registrations.
Biometric Security Safe Owner's Manual
Opening the safe for the first
time and using the override key:
To open the safe the first time or open without scanning a finger, the
override key can be used.
1 Remove the magnetic security cover
on the right side of the control panel.
2 Insert the override key
(the notch on the key handle must
be facing up) and turn counterclockwise.
3Rotating the key will retract the bolts and open the safe.
4Turn the key clockwise to remove the key.
5Replace the magnetic security cover.
6Do not store the override keys in the safe.
Installing batteries:
1Open the safe door and locate the battery case on the back of
the safe door.
2Slide the battery cover towards the bolts to open the battery
compartment.
3Install 4 new alkaline AA batteries and replace the battery cover.
For all safe models, we recommend the following:
• Refrain from using rechargeable or Non-Alkaline batteries.
• Use quality name brand batteries.
• All batteries have expiration dates on them. Ensure those dates are as
close to 10 years out from current year as possible.
• When changing batteries do not mix battery brands.
• When replacing batteries, do not mix old batteries with new batteries.
Replace all batteries at the same time.
Registering your fingerprint:
Important note - We highly recommend you add the same
fingerprint multiple times and adjust your finger’s angle and
location between each registration to ensure the safe opens
on the first attempt. As an example, during a single registration (3
scans), register the center of your fingerprint – try to use the exact
same finger location all three times. Then repeat the registration
process with the same finger, using the top of your fingerprint, again
trying to use the exact same finger location. Then repeat using the base
of your fingerprint, the sides of your fingerprint and so on.
Registering your fingerprint
continued:
1 When the door is open, press the red button on the back of the
door (near the hinge) for one second and release.
2 When you see the orange light on the control panel, hold your
finger on the sensor and wait until the orange light turns off.
The safe will be silent during this step.
3Remove your finger from the sensor.
4 Repeat steps 2 and 3 two additional times using the same
finger. Try to use the exact same finger location and angle. If
registration was successful a green light will flash and the safe
will beep twice.
If the registration process failed, a red light will flash and the
safe will beep three times. You will need to re-start at step 1 to
register your fingerprint.
Additional Notes: If the fingerprint memory is full, a red light
will flash and the safe will beep five times.
Opening the door:
Place your finger onto the biometric sensor and wait until the
green light turns on. The safe will beep twice and the door will
open automatically. If the safe does not recognize the fingerprint
(not registered or accepted), a red light will flash and the safe will
beep three times. The safe will remain locked. If batteries need
replacement, after a successful opening, a red light will flash and the
safe will beep three times.
Closing the door:
Hold the door completely closed and press the black button on the
left side of the control panel. The bolts will automatically engage and
lock the safe. If the door is not completely closed the bolts will stop,
the safe will beep 3 times and the safe will automatically re-open.
You will need to scan your finger again to reset the bolts and repeat
the closing process. The lock button will not work to move the bolts
during this event but returns to normal function after a successful
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Master Lock LX110B Sentrysafe bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Master Lock LX110B Sentrysafe in de taal/talen: Alle talen als bijlage per email.
De handleiding is 1.19 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.