705294
6
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
4
The Basics
We recommend that you fold out the inside back
cover of this manual so that diagrams of the
ampʼs front and rear panels are visible while you
read.
MAINS INPUT & FUSE (17)
Your amp is provided with a detachable mains
(power) lead, which is connected here. The
specific mains input voltage rating that your
amplifier has been built for is indicated on the
rear panel.
WARNING: Before going any further, make
sure your amplifier is compatible with your
electrical supply. If you have any doubt,
please get help from a qualified technician -
your Marshall dealer can help you in this
respect.
The correct value of mains fuse is specified on
the rear panel of the amplifier. NEVER attempt
to bypass the fuse or fit one of the incorrect
value.
Mains (POWER) Switch (1)
This is the On/Off switch for the mains electric
power to the amplifier.
Note: Please ensure the amplifier is switched off
and unplugged from the mains electricity supply
whenever it is moved!
INPUT Jack Socket (10)
You must always use a screened (shielded)
guitar cable and never use an unscreened
(unshielded) speaker cable. Also, this cable
should be one of good quality. If you are in any
doubt regarding this, your Marshall dealer will be
more than happy to help and advise you.
Getting Started & Powering Up
1. Make sure that the speakers/cabinet(s) are
connected to the correct impedance
LOUDSPEAKER jack(s) on the rear panel (11).
See page 8 for specifics regarding impedance
matching. If youʼre using an extension cabinet
make sure its rating is enough to handle the
power of the amp and also that youʼre using a
proper speaker cable. Never use a screened
(shielded) guitar cable for this purpose.
WARNING!
1. Failure to do any of the above will damage
your amp.
2. NEVER use your amp without a (speaker)
load attached when the Standby Switch is
ON.
Marshall recommends you always leave a
(speaker) load attached to the unit.
2. Ensure that both MASTER VOLUMES on the
front panel (5) are set to zero.
3. Connect the Footswitch Cable to the
Footswitch and then connect to the
FOOTSWITCH Socket (15) on the rear panel of
the amplifier.
4. Connect the supplied mains (power) lead into
the MAINS INPUT (17) on the rear panel first
and then into an electrical outlet.
5. Plug your guitar into the INPUT jack socket
(10) on the front panel.
6. Turn the front panel POWER switch (1) on.
This will glow red then wait for a couple of
minutes.
7. After waiting a couple of minutes, engage the
STANDBY switch (2). Leaving the amp on
ʻStandbyʼ for a period allows the valves to come
up to their correct operating temperature. In
order to prolong valve life, the STANDBY switch
should also be used to turn the amplifier on and
off during breaks in a performance.
STANDBY Switch & Silent recording (2)
As stated above the STANDBY Switch is used in
conjunction with the POWER Switch to ʻwarm
upʼ the amplifier before use and to prolong the
life of the output valves.
When the amplifier is in standby mode the
whole preamplifier section continues running at
its nominal voltages whilst the power amplifier
remains in a standby status. This allows the
amplifier to be used for silent recording or
preamplification purposes.
NOTE : Only when the STANDBY is off can
the amplifier be used without a load for silent
recording. Always ensure a load is
connected when leaving the silent recording
mode, i.e. when switching the STANDBY
switch ON.
ENGLISH
JVM 2 Ch Owners Manual Book-00089-01 /12/15 inner.qxd:Layout 1 14/12/15 10:08 Page 4
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marshall JVM210H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marshall JVM210H in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 9,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info