671531
2
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
COMPLIANCE STATEMENT
ENGLISH
The CODE footcontroller (PEDL-91009) has two Modes of operation: PRESET Mode and SWITCH Mode. NOTE: The footcontroller will always power on in Preset Mode.
SWITCH MODE
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. Consult the dealer
or an experienced radio/TV technician for help.
- To reinitialise your CODE footcontroller simply unplug and re-plug
the cable.
Industry Canada caution.
This device complies with Industry Canada licence-exempt
RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may
cause undesired operation of the device.
Francais:
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
Lexploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radio électrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
SWITCH Mode enables you to use footcon-
troller buttons 1 – 3 to activate or deactivate
assigned Section Switches and functions on the
amplier’s panel.
To enter SWITCH Mode from PRESET Mode,
press and hold any of the footcontroller but-
tons: 1 - 3.
NOTE: Press and hold the currently active but-
ton to change Mode without changing Preset.
Press and hold either of the remaining buttons
to change Mode while activating that button’s
assigned Preset.
The footcontroller display will show the Preset
number that you are currently on.
The three ASSIGNED SWITCH LEDs on the
right side of the footcontroller show the status
of the corresponding Section Switch: 1, 2 and
3. Red means the Section Switch is active, and
Green means it is inactive.
NOTE: The TAP Delay LED will ash red in time
with the current Tap Tempo Delay setting.
Footcontroller button 1 – 3 default Section
Switch assignment is:
1. PRE FX 2. MOD 3. DEL
To change the default Section Switch
assignments:
• Ensure the footcontroller is in SWITCH
mode.
• Press and hold your desired Section Switch
or Tuner/Tap Tempo function on the amplier
panel and then immediately select and
release the footcontroller button that you
wish to assign: 1 - 3.
• Your selected Section Switch or Tuner/
Tap Tempo function will now be assigned to
the corresponding footcontroller button.
• When you have assigned a panel function to
a footcontroller button, pressing EXIT/STORE
will return you to the main Preset screen.
• To overwrite it, repeat this process.
NOTE: To exit SWITCH Mode and return to
PRESET Mode, press the BANK footcontroller
button.
PRESET MODE
PRESET Mode enables you to assign any of
CODE’s 100 Presets to 30 locations within
the footcontroller. That’s ten Banks, each
containing three Presets.
The footcontroller’s two-digit display shows
on its left the BANK that you are currently
on (A –J), and on its right it shows the Preset
location NUMBER you are currently on: 1, 2
or 3, which correspond with footcontroller
buttons 1, 2 and 3.
The fourth footcontroller button selects the
BANK. Press once to increment the BANK.
Press and hold to decrement the BANK.
When you have selected your BANK, the
location NUMBER will ash on the display,
indicating a location has not been chosen.
Press footcontroller button 1 – 3 to select
your location.
Storing a Preset to a footcontroller location:
• Select a Preset on your CODE amplier
that you wish to store to the footcontroller.
• Choose a location on the footcontroller
that you wish to store to: BANK A - J.
• While holding down the EXIT/STORE
switch on the amplier panel, press and
release the desired button on the
footcontroller: 1 - 3.
• Your chosen Preset will now be recalled
when you select that footcontroller location.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marshall Code - PEDL-91009 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marshall Code - PEDL-91009 in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info