494308
5
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
ENGLISH
5SW10
TM
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House
Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or
Marmitek Security Console installed in your house. These components will translate the radio
signals to the Marmitek X-10 signal on the power line. Only one Transceiver should be
installed for all remotes and sensors set to the same House Code.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your
remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to
be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power
line before transmitting their data. To prevent your Marmitek X-10 System to become slow or
to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as
far away from each other as possible.
USER INSTRUCTIONS SW10 SHUTTER SWITCH
SWITCH OFF APPROPRIATE MAINS FUSE BEFORE INSTALLING!
(INSTALLATION BY A CERTIFIED INSTALLER)
1. Take of the switch cover, remove both screws and take off the mounting plate.
2. Mount the mounting plate onto the flush mounting box with countersunk screws.
Position the plastic décor frame.
3. Connect cables:
Phase to L (_)
Neutral to N
UP to UP
Down to DN
4. When connected, position Shutter Switch on the mounting plate and reinsert both screws.
5. Now program the switch using the following procedure:
PROGRAMMING THE SW10
Now the control electronics has to be calibrated in order to adjust to the time the shutter
motor need from fully closed to fully open:
1. Switch on mains fuse.
2. Use the switch to drive the shutter all the way up.
3. With the aid of a screwdriver, adjust the House Code dial to the * position.
4. Now press the lower push button until the shutter is closed completely.
5. Release the button as soon as the shutter is closed. The electronics measure the elapsed
time and stores it internally so that the switch always knows the position of the shutter.
6. Set the rotary code switches on the front side to the desired address
7. Put the switch cover back on.
The calibration is now completed. The internal electronics have measured and stored the time
for raising and lowering the shutter. These values will not be lost even in case of mains fail-
ure. You are now able to control the switch both by hand and with a Marmitek X-10
Controller (the switch will not respond to Marmitek X-10 signals when the programming has
not been executed).
The switch will respond to the following commands: ON: fully open, OFF: fully closed,
DIM : 4 % up, BRIGHT: 4 % down.
SW10.qxd 02-11-2006 17:20 Pagina 5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek SW10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek SW10 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info