494336
3
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
13
Marmitek is niet verantwoordelijk voor het disfunctioneren
van het Marmitek X-10 -systeem als gevolg van in het
gebouw aanwezige apparatuur met emissiewaardes boven de
maximale toegestane niveaus zoals die gelden in residentiële,
commerciële en lichtindustriële omgevingen en zijn
vastgelegd in de EN 61000-6-3.
Toepassing Geldende Europese norm Marmitek X-10 -huis
automatisering*
Immuniteit van Emissie van Immuniteit- en
de apparatuur de apparatuur emissienorm
Residentieel 61000-6-1 61000-6-3 Compatibel/
Commercieel voldoet
Licht-industrieel
* Voorwaarde daarbij is dat het gehele Marmitek X-10 -systeem wordt
geïnstalleerd volgens de geldende instructies door een gecertificeerde
en getrainde Marmitek X-10 -dealer.
Copyrights
Marmitek is a trademark of Pattitude B.V., SAX35™ is a trademark of
Marmitek B.V. All rights reserved. Copyright and all other proprietary
rights in the content (including but not limited to model numbers,
software, audio, video, text and photographs) rests with Marmitek B.V.
Any use of the Content, but without limitation, distribution, reproduction,
modification, display or transmission without the prior written consent of
Marmitek is strictly prohibited. All copyright and other proprietary notices
shall be retained on all reproductions.
20360 - 2010929
Marmitek X-10
Potential-free actuator/interface
type SAX35
For connecting
external devices
to Marmitek X-10
PROG.
N
L
SAX
35
16
Marmitek X-10 Potential-free input/output interface type SAX35
Description
Module with:
Two galvanically separated potential-free inputs for
transposing contact outputs on external devices into
Marmitek X-10 power line commands.
One galvanically separated potential-free relay contact output
for transposing Marmitek X-10 power line signals for opening
and/or closing of a relay contact.
Connection
Mains connection via fixed mains cable.
Galvanically separated relay contact with 2 screw terminals:
normally open contact.
Galvanically separated inputs with 4 screw terminals with
common “+” connection.
Application
On one side, the module can be connected directly to the mains
and on the other side, via the built-in galvanic separation, to
peripheral equipment to send 2 Marmitek X-10 addresses and
receive 1 Marmitek X-10 address. The module must be
connected to other equipment such as a personal alarm system,
burglar alarm system or other equip ment to make this
equipment suitable for use with the Marmitek X-10 .
17
Operation
The SAX35 can transpose two galvanically separated contact
inputs to Marmitek X-10 addresses, plus on or off commands.
The addresses are defined by the programmed send address of
the module. The inputs are activated by an external DC or AC
voltage of 5 V to 25 V.
The SAX35 can also transpose a received Marmitek X-10
address plus command to open or close the relay contact. This
output is suitable for 5 A AC or DC.
Which Marmitek X-10 address is transposed is defined during
the programming of the SAX35. To do so the module needs to
be provided with a receive address. The relay contact is also
galvanically separated from the input wires.
Connection terminals
Description Explanation
Input 1 Programmed send address
(V+ on + with DC supply)
Input 2 Programmed send address +1
(V+ on + with DC supply)
Relay contact Programmed receive address
18
Programming
Always switch on the power before programming.
Avoid the contact with life parts!
Programming the SAX35
To define which Marmitek X-10 addresses correspond to the
inputs and relay contact, the SAX15 included in the SAX35
needs to be programmed.
The address of input 1 and the relay contact output can be
selected independently.
The second input is automatically allocated the next higher
address. Remember that the input and output addresses should
not overlap and ensure that the base input address is always at
least two higher than the base output address. If the base
address is set to 16, the second connected address will be 1.
Programming mode
Activating programming mode
The SAX35 needs to be set into programming mode as follows:
Press the program button for at least three seconds,
see Figure 1, so that the red LED lights up when the button
is released.
!
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek SAX35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek SAX35 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info