494335
4
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
19
Standard settings
The phase coupler/repeater will automatically, from its factory
settings, transfer and repeat Marmitek X-10 commands from
one phase to the other. The signals are transmitted (repeated) to
all phases at the maximum transmission level. In general, the
phase coupler will operate best in the standard setting.
However, under special circumstances it may be necessary to
change the settings.
Please note:
We recommend that, if in doubt, you do not change
the phase coupler's settings.
!
Programming
20
Programming
Changing the FKX40 settings
Only in certain circumstances is it necessary to change the
settings of the phase coupler.
The following programming options are available:
Standard Optional Setup LED
Commands Indication
Repeater
2 x ABright Status LED 1: ON
Phase 1 ON*)
Repeater
2 x ADim Status LED 1: OFF
Phase 1 OFF
Repeater
2 x BBright Status LED 2: ON
Phase 2 ON*)
Repeater
2 x BDim Status LED 2: OFF
Phase 2 OFF
Repeater
2 x CBright Status LED 3: ON
Phase 3 ON *)
Repeater
2 x CDim Status LED 3: OFF
Phase 3 OFF
Coupler
2 x ON Receive LED 1: ON
Function ON*)
Coupler
2 x OFF Receive LED 1: OFF
Function OFF
21
Standard Optional Setup LED
Commands Indication
Default *) - - - Receive LED 3: OFF **)
Reset 2 x
LEDs and settings
to default All Lights On
according to factory
settings
*) Default factory setting.
**) In programming mode "Receive LED 3" will blink for 0.5 s when set-up commands
are being received.
Option description:
Repeater Phase 1 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Repeater Phase 2 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Repeater Phase 3 OFF: Received Marmitek X-10 commands
will not be repeated on this phase.
Coupler function OFF: Received Marmitek X-10 commands
will not be repeated to other phases.
This option can be used in test
situations.
Reset to factory settings: All options will be reset to the factory
settings.
22
Programming
Activating the programming mode:
The FKX40 must be set to the programming mode as follows:
Press the program button
for at least three seconds
(see Figure 3) until the
yellow LED lights up. The
Status/Receive LEDs now
display the activated
options.
Send the set-up commands
that correspond to the
desired setting(s) over the
power line to the FKX40
via a PMIX35.
Deactivating the programming mode:
Briefly press the program button or wait 60 seconds so that
the programming function deactivates automatically.
STATUS 1
PROGRAM
STATUS 1
STATUS 1
RECEIVE 1
RECEIVE 2
Phase Coupler/Repeater
FKX40
L1 L2 L3 N
RECEIVE 3
Figuur 3.
23
In programming mode the yellow LED "Program" is ON and the
Status/Receive LEDs indicate the activated options. The
programming mode can therefore also be used to check the
phase coupler's settings.
Observation: All LEDs are off. The yellow "Program" LED does not
blink every three seconds.
Checklist: Check whether there is any voltage and check the feeder circuit
of the circuit breaker to the FKX40.
Observation: The Status LED and the Receive LED for the same phase
are on constantly.
Checklist: Check the power connection for this phase on the FKX40.
Observation: One or more Receive and Status LEDs are blinking
constantly.
Step 1:
Set the FKX40 to programming mode and check whether Receive
LED 2 is on. If it is on, send the "Status ON" command twice over
the power line via a PMIX35 to deactivate the underlying
function. Receive LED 2 should go off. Exit the programming
mode. If this does not solve the problem, go to the next step.
Troubleshooting
24
Troubleshooting
Step 2: Set the FKX40 to programming mode and set option "Coupler
function OFF" (Receive LED 1: OFF). Exit the programming mode
and check whether this solves the problem.
Reset the FKX40 to programming mode and set option "Coupler
function ON" (Receive LED 1: ON). If this does not solve the
problem, go to the next step.
Step 3: Check the phase that corresponds to the blinking LED for any
component or equipment faults.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marmitek FKX40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marmitek FKX40 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info