571043
5
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
PREPARATIONFORUSE
Rear panel Signal Connection
All signal connections to the Model 1060 should be
made with shielded audio cables. Figure 2 shows
the location of the input and output jacks on the
rear panel. These are for "permanent" connections.
Use of the front panel controls and jacks will be
discussed later. A letter "L" corresponds to the left
audio channel; a letter "R" to right audio channel.
To avoid confusion, it is suggested that you
connect one cable at a time between the Model
1060 and the other components of your system.
This way, mixing up the channels or mixing up
signal sourcesand destinations will be avoided.
D
The SPEAKER SYSTEM (MAIN, REMOTE) jacks
on the left side of the rear panel will accomodate
two loudspeaker systems; each speaker having a
rated impedance between 4 and 16 ohms. When
using only one pair of speakers, connect them to
the terminals marked MAIN. The terminals marked
REMOTE are used for connection a second pair of
speakers in a location remote to the Model 1060.
u
Use care when connecting the Model 1060 to a
loudspeaker which contains a built-in power
supply-such as an electrostatic loudspeaker. The
"common" speaker-connection terminal of these
devices may be capacitively coupled through the
power supply. Ensure that the (-) terminals of the
model 1060 are connected to the "common"
SYSTEM 1 REPEAT WIRI NG
AS FOR SYSTEM 1
+
COM.
RIGHT
LEFT
Figure1. LoudspeakerSystem Connections
terminals of the loudspeaker system as shown in
Figure 1. Ordinary #18 gaugetwo-conductor lamp
cord may be used for distances of up to 30 feet
between amplifier and loudspeakers. For longer
distances, use#16 gaugewire or heavier, depending
on length.
In connecting two loudspeakers for stereo opera-
tion, it is important to insure correct relative
phasing (polarity). This is best acheived, when
using identical loudspeakers, by simply coding each
wire for identification, one wire in each pair
should be coded at both ends with a knot, tape,
etc. The coded wires can then be used for identical
connections in each channel. For example, the
coded wire in each pair can be connected to the
"common" terminal of each loudspeaker and the
(-) terminal of each amplifier channel. The un-
coded wire of each pair is then connected to the
remaining loudspeaker terminal and the remaining
terminal on each amplifier channel (R and L). This
procedure insures correct polarity or phasing of
identical loudspeakers.
Note: Close inspection of standard zipcord will
reveal some form of coding on the insulation (ridge
or groove on one edge); or one of the wires may be
tinned and the other wire not tinned.
CAUTION: Never directly connect the loudspeaker
terminals of one channel in parallel with those of
any other. Any resulting damage is not covered
under warranty.
2
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marantz Model 1060 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marantz Model 1060 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info