636181
33
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
Operating instructions, Comfort 360, 370, 380 (#101258 – EN) 33
EN
10. Troubleshooting
Faults without the error message display
LCD display has no display and does not light up.
Drive in standby mode.
Press an arbitrary button to put the drive into the
operating mode.
Note:
This can start the door moving.
Voltage missing.
Check whether mains voltage is present.
Check current connection.
Thermal contactor in mains transformer has
triggered.
Leave the mains transformer to cool down.
Controller unit defective.
Have the drive system checked.
No response after pulsing.
Connectionterminalsfor“Pulse”buttonbypassed,e.g.
throughlineshort-circuitoratterminal.
Possibly test-disconnect wired key switch or
internal push-button from the controller unit:
Unplug cable from socket XB03, insert short-
circuit plug and search for wiring fault.
“3.4.3Connectionofpotential-freebutton(XB03)”
No response after pulsing by hand-held transmitter.
Module receiver not plugged in.
Connect module receiver with controller unit.
“3.5Completingtheinstallation”
Hand-held transmitter coding does not match
receiver coding.
Reactivate hand-held transmitter.
“4.5Quickprogramming”
Hand-held transmitter battery empty.
Insert new battery.
“5.2Hand-heldtransmitter”
Radiooperationdeactivated(“externalbutton”symbol
ashes).
Press the + (OPEN) or – (CLOSE) button on the
drive to reactivate the radio.
Hand-held transmitter or controller electronics or
module receiver defective.
Have all 3 components checked.
Drive system reverses with interruption to frame photocell.
Programming was not performed correctly. Frame
photocellwasnotidentiedcorrectly.
Manually set the position of the frame photocell.
“Level8,Menu10-Positionoftheframephotocell”
Faults without the error message display
Low or no range.
Hand-held transmitter defective.
Check hand-held transmitter, replace if
necessary.
Antenna defective or installed incorrectly.
Check / replace antenna.
Lay antenna to the lintel or feed out of the garage,
if nec. install outside antenna.
Faults on frequency band used.
Switch to alternative frequency.
Drive lighting not working.
Bulb defective.
Replace LED.
With further faults.
Observe error message (see LCD display).
Have article no., production no. and version
to hand (see type plate) for any queries.
Reset and re-commissioning in accordance with
the operating manual.
Faults with error message display
The display shows detected faults with an
error number (example error number 7).
The controller switches to the message
mode.
In operating mode, pressing the P button
displays the most recent error number.
Error number 7
After 120 seconds without pressing a button,
programming mode switches off automatically.
Restart the programming procedure.
Error number 9
Speed sensor pulse not available,
drive system blocked.
Have the drive system checked.
33

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Marantec-Comfort-370

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Marantec Comfort 370 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Marantec Comfort 370 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Marantec Comfort 370

Marantec Comfort 370 Gebruiksaanwijzing - Nederlands - 26 pagina's

Marantec Comfort 370 Gebruiksaanwijzing - Deutsch - 36 pagina's

Marantec Comfort 370 Gebruiksaanwijzing - Français - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info