386595
6
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Reversing switch action (Fig. 7)
CAUTION:
Always check the direction of rotation before opera-
tion.
Use the reversing switch only after the machine
comes to a complete stop. Changing the direction of
rotation before the machine stops may damage the
machine.
This machine has a reversing switch to change the
direction of rotation. Slide the reversing switch up for
clockwise rotation or slide it down for counterclock-
wise rotation.
Overload protector
The overload protector automatically cuts out to break
the circuit whenever heavy work is prolonged. Wait
20 30 seconds before resuming operation.
Adjusting the fastening torque (Fig. 8)
The fastening torque can be adjusted infinitely from
approx. 20 kg·cm to 80 kg·cm. To adjust it, loosen the
two screws and turn the adjusting ring. Then tighten
the screws to secure the adjusting ring. Refer to the
table below for relation between the numbers on the
adjusting ring and the fastening torque to be obtained.
Numbers on
adjusting ring
Fastening torque to
be obtained
1 20 kg·cm
2 35 kg·cm
3 48 kg·cm
4 60 kg·cm
5 80 kg·cm
(Example)
35 kg·cm of fastening torque can be obtained when
the number 2 is aligned to the red mark.
NOTE:
Always tighten the two screws to secure the adjust-
ing ring after adjusting the fastening torque.
The fastening torque may differ depending upon the
kind of screws, the type of materials to be fastened,
etc. Before starting your job, always perform a test
operation to verify the adequate fastening torque.
Operation
The proper fastening torque may differ depending
upon the kind or size of screws, the type of materials
to be fastened, the condition of the threads, etc.
Before starting your job, always perform a test opera-
tion to verify adequate fastening torque.
Hold the machine firmly with both hands whenever
possible and place the socket over the bolt or nut.
Then turn the machine on. As soon as the bolt or nut
becomes tight, the clutch will cut in and the motor will
stop automatically. Release the switch trigger.
When fastening machine screws, use the proper
screwdriver bit shown in Fig. 9. It is commonly avail-
able on the market.
NOTE:
Always use the correct size socket for bolts and
nuts. An incorrect size socket will result in inaccu-
rate and inconsistent fastening torque and/or dam-
age to the bolt or nut.
Hold the machine with its square drive pointed
straight at the bolt or nut, or the bolt or nut will be
damaged.
If the motor will not start even after you pull the
trigger, release the trigger. Then pull the trigger
again after turning the socket slightly with your
fingers.
Fastening performance
The following reference table indicates the approximate fastening capacity from a single 1-hour battery charge.
It may differ under some conditions.
Screw size Fastening torque Fastenings
M6x14
5 About 800 screws
1 About 1,000 screws
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off and
the battery cartridge is removed before carrying out
any work on the machine.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
Makita Authorized Service Center.
6
6702D (E) (’97. 9. 19)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita dw 6702 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita dw 6702 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info