389731
6
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
6
Installing paper dust bag
To install the paper dust bag, place the paper dust
bag on the paper dust bag holder with its front side
upward. Insert the front fixing cardboard of the paper
dust bag into the groove of the paper dust bag holder.
(Fig. 6)
Then press the upper part of the front fixing card-
board in arrow direction to hook it onto the claws.
(Fig. 7)
Insert the notch of the paper dust bag into the guide
of the paper dust bag holder. Then install the paper
dust bag holder set on the tool. (Fig. 8 & 9)
Front grip (Fig. 10)
Install the front grip on the tool so that its protrusions
fit into the matching notches in the front of the tool.
Secure the front grip using a screwdriver to tighten
the screw through the hole in the front grip.
Switch action (Fig.11)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the trigger. Release the
trigger to stop. For continuous operation, pull the trig-
ger and then push in the lock button. To stop the tool
from the locked position, pull the trigger fully, then
release it.
Speed adjusting dial (Fig. 11)
For BO5021 only
The tool speed can be infinitely adjusted between
4,000 opm and 12,000 opm by turning the speed
adjusting dial, which is marked 1 to 5. Higher speed
is obtained when the dial is turned in the direction of
number 5; lower speed is obtained when it is turned
in the direction of number 1. Refer to the figure below
for the relationship between the number setting on
the adjusting dial and the kind of work.
A range: For polishing
B range: For finish sanding
C range: For regular sanding
NOTE:
The above figure shows standard applications. They
may differ under certain conditions.
Sanding operation (Fig. 12)
Turn the tool on and wait until it attains full speed.
Then gently place the tool on the workpiece surface.
Keep the pad flush with the workpiece and apply
slight pressure on the tool.
CAUTION:
Never run the tool without the abrasive disc. You
may seriously damage the pad.
Never force the tool. Excessive pressure may
decrease the sanding efficiency, damage the abra-
sive disc or shorten tool life.
•ON-LOA
DO
FF-LOAD
The sanding pad rotates clockwise during the loaded
operation, but it may rotate counterclockwise during the
no-load operation.
Polishing operation
For BO5021 only
CAUTION
Use only a Makita genuine sponge pad, felt pad or
wool pad (optional accessories).
Always operate the tool at low speed to prevent
work surfaces from heating abnormally.
Never force the tool. Excessive pressure may
decrease the polishing efficiency and cause motor
overload, resulting in tool malfunction.
1. Applying wax (Fig.13)
Use an optional sponge pad. Apply wax to the
sponge pad or work surface. Run the tool at low
speed to smooth out wax.
NOTE:
First, wax a not conspicuous portion of the
work surface to make sure that the tool will not
scratch the surface or result in uneven waxing.
Always run the tool at low speed. Running it at
high speed may cause the wax to spatter.
2. Removing wax (Fig. 14)
Use an optional felt pad. Run the tool at low
speed to remove wax.
3. Polishing (Fig. 15)
Use an optional wool pad. Run the tool at low
speed and apply the wool pad gently to the work
surface.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
Makita Authorized Service Center.
12
3
45
4000
12000
A range
B range
C range
Dial setting
Orbits per minute
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita bo 5020 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita bo 5020 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Noors als bijlage per email.

De handleiding is 0,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info