448668
14
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
14
Testing the run-out brake
MAINTENANCE
Sharpening the saw chain
When working on the saw chain you must always pull
out the power supply plug and wear protective gloves.
A
The chain needs sharpening when:
- the sawdust from sawing humid wood looks like wood flour.
- the saw chain penetrates the wood only under great
pressure.
- the cutting edge is visibly damaged.
- the sawing device is pulled to the left or the right during the
sawing operation. This is caused by uneven sharpening of
the chain or by damage to one side of it.
Important: Sharpen frequently, but without removing
too much metal!
Generally, 2-3 strokes of the file will be enough.
Have the chain resharpened in a service center when you
have sharpened it yourself several times.
Checking the chain lubrication
Never saw when a sufficient chain lubrication is not guaranteed.
Otherwise the life of the sawing device will be reduced. Before
starting work check the oil level in the tank and the oil feeding.
Check the fed oil quantity by following the instructions below:
- Start the electric chain saw.
- Hold the running chain saw approx. 15 cm above a trunk or
the ground (use an appropriate surface).
If the lubrication is sufficient, you will see a light oiltrace
because oil will be centrifuged from the chain saw. Pay attention
to the direction the wind is blowing and avoid unnecessary
exposure to the oil spray!
J
Proper sharpening:
CAUTION:
Use only chains and guide bars designed for this saw (see
the Extract from the spare-parts list)!
- All cutters must be of the same length (dimension a).
Cutters with different lengths result in rough running of the
chain and can cause cracks in the chain.
- Minimum cutter length is 3 mm (0.11"). Do not resharpen
the chain when the minimum cutter length has been reached;
at this point, the chain must be replaced (see the Extract
from the spare-parts list and "Replacing the chain").
- The depth of the cut is determined by the difference in
height between the depth limiter (round nose) and the
cutting edge.
- The best results are obtained with a depth-limiter depth of
0.65 mm (.025").
CAUTION:
Excessive depth increases the
risk of kickback!
B
min.
3 mm (0.11”)
Do not work with the saw without first testing the run-out
brake!
- Start the motor as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
- Grasp the tubular handle firmly with one hand and hold the
grip with the other.
- Switch the motor on and then back off. The chain should
come to a full stop within two second of switching off the
motor.
Important: If the saw chain does not stop within two
second when you carry out this test, do not use the
saw! Inspect the carbon brushes (see page 16).
I
0.65 mm
(.025")
0.65 mm
(.025")
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita UC 3001A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita UC 3001A in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita UC 3001A

Makita UC 3001A Gebruiksaanwijzing - Deutsch - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info